Robotics By BIGTREETECH

• Main Control Chip: Adopt STMicroelectronics' latest G0 series main control chip STM32G0B1RET6 or STM32G0B0RET6
• Three CNC Fan: Increase the heat dissipation controllable fan to reduce the printer temperature when the device is working
• Increased Heat Sink: Redesign the drive heat sink, strengthen the drive heat dissipation capacity, and greatly improve the heat dissipation performance
• Output Power Supply: Increase SPI output port +3.3V power supply, external SPI sensor power supply voltage +3.3V and +5V are optional, support the motherboard to directly supply power to peripherals
• TFT35-E3 V3.0.1 Screen: This touch screen panel board has higher compatibility. Users can select two work modes: UART serial port screen mode and 12864 screen mode; Serial port screen mode supports two printing modes: SD card and U disk

• High-performance Kit: BL Touch V3.1 auto bed leveling senor is controlled by hall effect, providing high precision. Thus the bed material can be selected freely, glasses/ wood/metal etc. The stroke is up to 1.6mm longer than V2.0
• High Precision: BLTouch's Standard Deviation in repeatability is around 0.005mm. The 3D printer automatically detects the bed surface, and adjusts the perfect distance. Logic Voltage Free(Open Drain Output) is 3.3V / 5V The desired output logic voltage is stored in the EEPROM of the probe and can be selected by commands
• Premium Leveling Kit: There're 1 set of bltouch auto bed leveling sensor kit and 2 types extension cables included in the package.?1.5m extension for CR10 Series, 1M extension wire for Ender series)
• Wide Application: This Bltouch V3.1 auto bed leveling kits are compatible with 32-bit V4.2.7, BTT SKR MINI E3 V3.0/Octopus/Manta/SKR 3/EZ/V1.4 Turbo, Kraken Series, MKS Gen L board, suitable for Ender 3, Ender 3 V2, Ender 3 MAX, Ender 3 Pro, Ender 3S, Ender 5, Ender 5 Pro, CR-10 etc..3D Printers
• For More Information: If you want more details about BLTouch and 2 extension cables, please check out the antclabs github. If you have any problems during use, please wirter to us through amazon at the first time. We will give you a satisfactory solution

• BIGTREETECH Manta M8P Control Board uses 32-bit ARM Cortex-M0+ series STM32G0B1VET6 main control chip with a core frequency of 64MHz. High-performance MOSFETs are used to reduce heat generation
• The power chip of Manta M8P integrated main control board adopts TPS5450-5A, which supports DC12/24V power input; the output current of this chip is up to 5A, and the peak value can reach 6A, which perfectly supports the power supply of Raspberry-Pi
• The control board and the core board use BTB connection method, so that other core board solutions other than CM4 can be selected, such as BIGTREETECH CB1. The mainboard reserves the SPI expansion interface for using the Klipper firmware to connect an external acceleration sensor for acceleration compensation
• The thermistor can select the pull-up resistance value through the jumper, which supports PT1000 without external modules, which is convenient for DIY use; the control board reserves a three-way four-wire fan interface, which can be used to connect a water cooling device
• The MCU firmware can be upgraded through SD card, or through DFU through Klipper's make flash command; the main board reserves the proximity switch interface, supports NPN and PNP type selection, (24V, 12V, 5V) voltage optional, shared with VFAN6 Voltage selection

• Main Control Chip: Adopt STMicroelectronics' latest G0 series main control chip STM32G0B1RET6 or STM32G0B0RET6
• Three CNC Fan: Increase the heat dissipation controllable fan to reduce the printer temperature when the device is working
• Increased Heat Sink: Redesign the drive heat sink, strengthen the drive heat dissipation capacity, and greatly improve the heat dissipation performance
• Output Power Supply: Increase SPI output port +3.3V power supply, external SPI sensor power supply voltage +3.3V and +5V are optional, support the motherboard to directly supply power to peripherals
• BLTouch V3.1: BLTouch is an auto leveling sensor for 3D Printers based on open-source.Simple, Smart, High-precision.It could work with any kinds of bed materials, such as glasses, woods, metals, and so on. This kit with 80cm extension wire

• High-performance Kit: BL Touch V3.1 auto bed leveling senor is controlled by hall effect, providing high precision. Thus the bed material can be selected freely, glasses/ wood/metal etc. The stroke is up to 1.6mm longer than V2.0
• High Precision: BLTouch's Standard Deviation in repeatability is around 0.005mm. The 3D printer automatically detects the bed surface, and adjusts the perfect distance. Logic Voltage Free(Open Drain Output) is 3.3V / 5V The desired output logic voltage is stored in the EEPROM of the probe and can be selected by commands
• Premium Leveling Kit: There're 1 set of bltouch auto bed leveling sensor kit and 2 types extension cables included in the package.?1.5m extension for CR10 Series, 1M extension wire for Ender series)
• Wide Application: This Bltouch V3.1 auto bed leveling kits are compatible with 32-bit V4.2.7, BTT SKR MINI E3 V3.0/Octopus/Manta/SKR 3/EZ/V1.4 Turbo, Kraken Series, MKS Gen L board, suitable for Ender 3, Ender 3 V2, Ender 3 MAX, Ender 3 Pro, Ender 3S, Ender 5, Ender 5 Pro, CR-10 etc..3D Printers
• For More Information: If you want more details about BLTouch and 2 extension cables, please check out the antclabs github. If you have any problems during use, please wirter to us through amazon at the first time. We will give you a satisfactory solution