Hardware Adhesives & Sealers By J.V. Converting

• Produced in the USA. To ensure getting high-grade U.S.-made material please ensure the seller is FindTape. FindTape FELT-06 Polyester Felt Tape, 1 millimeter thick, is synthetic needle-punched felt made from polyester fibers. On one side, it is felt; on the other side, adhesive.
• This tape is most frequently used to join and temporarily repair curtains, fabric and cloth drapes used in backdrops and for other general use vibration dampening. There are many other kinds of uses as well.
• Tape rolls are typically cut to standard tape industry metric-cut sizes - or approx 5% narrower than the nominal size (i.e. 24mm per 1-inch of nominal width ordered).
• Adhesive: synthetic rubber. Carrier/Backing: polyester needled felt. Release Liner: paper (reverse wound). Thickness: 49 mils (carrier, adhesive, liner) 39 mils (carrier, adhesive) 10 mils (liner). Adhesion: 130 ounces per inch (to stainless steel test panel)
• Tensile Strength: 23 pounds per inch (longitudinal) 21 pounds per inch (transverse). Service/Operating Temperature: -30?F to 150?F. Application Temperature: 60?F (minimum). Standards Met: meets RoHS Directive 2011/65/EU. Core: 3 inch diameter

• Adhesive: natural rubber
• Thickness: 12 mils (carrier, adhesive)
• Adhesion: 50 ounces per inch (to stainless steel)
• Tensile Strength: 44 pounds per inch (longitudinal)

• Produced in the USA. FindTape FELT-09 Polyester Felt Tape is a 4mm thick synthetic needle punched felt made from polyester fibers. One side is felt, and the other side has adhesive. Commonly used for joining and temporarily repairing fabric, curtains and cloth drapes in backdrops.
• On many of the adhesive felt products the rolls will have an approximately 2-inch to 4-inch leader of double-sided film tape applied to the release liner before the felt material starts. We recommend you either cut a small piece of felt off at the beginning of the roll with a pair of scissors to start, or peel the double-sided film tape off of the release liner to use as a way to begin applying the felt (try not to pull the double-sided film tape off of the felt backing though).
• It is sometimes easier to try to peel the corner of the felt away from the release liner (instead of the release liner away from the felt) since you may end up splitting the release liner when you do it that way.
• Felt material is also used for filtration applications, gaskets, wipers, and padding in a wide variety of industries. FindTape FELT-09 hides seams being photographed and is used for applying a clean, dark edge to platforms, flats, and portals. Can also be used to create matte borders or edges and to line display and jewelry cases.
• Carrier/Backing: polyester felt; Adhesive: synthetic rubber; Service/Operating Temperature: -30F to 150F. Application Temperature: 60F (minimum); Thickness: 166 mils (carrier, adhesive, liner) 156 mils (carrier, adhesive) 10 mils (liner); Adhesion: 130 ounces per inch (to stainless steel test panel).

• Fluorescent

• Removable

• JVCC Stage-Set Spike Tape is available in 50-yard rolls: fluorescent green, fluorescent pink, fluorescent orange and fluorescent yellow, and in 55-yard rolls: black, brown, burgundy, dark green, grey, purple, red, tan, teal, white and yellow, which are cut from Polyken 510 source material.
• Keep a roll of JVCC Stage-Set Spike Tape on hand during your next theatrical or entertainment production for marking the stage for props, actor cues, and various other applications.
• This .5-inch wide gaffers tape promises residue-free removal and can easily be torn by hand so that you can quickly markup stages, bundle wires, and color-code props.
• JVCC Stage-Set Spike Tape is uniquely designed for a non-reflective look, so it can be used in photography and videography applications.
• Product applications include marking stages, color-coding, labeling, gaffing lights, bundling wires, and more.

• Produced in the USA. To ensure getting high-grade U.S.-made material please ensure the seller is FindTape. FindTape FELT-06 Polyester Felt Tape, 1 millimeter thick, is synthetic needle-punched felt made from polyester fibers. On one side, it is felt; on the other side, adhesive.
• This tape is most frequently used to join and temporarily repair curtains, fabric and cloth drapes used in backdrops and for other general use vibration dampening. There are many other kinds of uses as well.
• Tape rolls are typically cut to standard tape industry metric-cut sizes - or approx 5% narrower than the nominal size (i.e. 24mm per 1-inch of nominal width ordered).
• Adhesive: synthetic rubber. Carrier/Backing: polyester needled felt. Release Liner: paper (reverse wound). Thickness: 49 mils (carrier, adhesive, liner) 39 mils (carrier, adhesive) 10 mils (liner). Adhesion: 130 ounces per inch (to stainless steel test panel)
• Tensile Strength: 23 pounds per inch (longitudinal) 21 pounds per inch (transverse). Service/Operating Temperature: -30?F to 150?F. Application Temperature: 60?F (minimum). Standards Met: meets RoHS Directive 2011/65/EU. Core: 3 inch diameter

• Fluorescent

• Produced in the USA. FindTape FELT-09 Polyester Felt Tape is a 4mm thick synthetic needle punched felt made from polyester fibers. One side is felt, and the other side has adhesive. Commonly used for joining and temporarily repairing fabric, curtains and cloth drapes in backdrops.
• On many of the adhesive felt products the rolls will have an approximately 2-inch to 4-inch leader of double-sided film tape applied to the release liner before the felt material starts. We recommend you either cut a small piece of felt off at the beginning of the roll with a pair of scissors to start, or peel the double-sided film tape off of the release liner to use as a way to begin applying the felt (try not to pull the double-sided film tape off of the felt backing though).
• It is sometimes easier to try to peel the corner of the felt away from the release liner (instead of the release liner away from the felt) since you may end up splitting the release liner when you do it that way.
• Felt material is also used for filtration applications, gaskets, wipers, and padding in a wide variety of industries. FindTape FELT-09 hides seams being photographed and is used for applying a clean, dark edge to platforms, flats, and portals. Can also be used to create matte borders or edges and to line display and jewelry cases.
• Carrier/Backing: polyester felt; Adhesive: synthetic rubber; Service/Operating Temperature: -30F to 150F. Application Temperature: 60F (minimum); Thickness: 166 mils (carrier, adhesive, liner) 156 mils (carrier, adhesive) 10 mils (liner); Adhesion: 130 ounces per inch (to stainless steel test panel).

• Adhesive: natural rubber
• Thickness: 12 mils (carrier, adhesive)
• Adhesion: 50 ounces per inch (to stainless steel)
• Tensile Strength: 44 pounds per inch (longitudinal)

• JVCC FELT-N1 Nomex Felt Tape is made from 100% meta-aramid synthetic fibers which do not ignite, melt or drip and retain their mechanical properties at elevated temperatures.
• Even though meta-aramid fibers have higher tensile strength and lower thermal conductivity than other fibers, they are soft to handle and processes similar to conventional fibers.
• JVCC FELT-N1 Nomex Felt Tape is 1/8 inches thick and provides proven performance as a lightweight and durable solution for a range of applications and industries where heat and flame-resistance are vital.
• In addition, JVCC FELT-N1 Nomex tape can be used in high-temperature applications for sealing or protection against scratches and dents. Product applications include flame-resistant clothing. military, personal protective equipment, grills, and BBQ equipment, aerospace, high-temperature gaskets, and scratch and dent protection.
• Adhesive: synthetic polymer. Release Liner: paper. Tensile Strength: 3.5 pounds per inch (longitudinal). Application Temperature: 600F (maximum). Fiber Type: Aramid. Construction: 100% needle punch. Weight: 8 oz per sq. yd. +/- 10%. Core: 3-inch diameter.