Power Transmission Products By uxcell

• 6300-2RS (I.D.=10mm, O.D.=35mm, Thickness=11mm)
• 6300 2RS bearings are sealed on BOTH SIDES to keep lubricant in
• Made from Carbon Steel, durability and resistance to under heavy loads
• ABEC Tolerance 1 (P0), Z2 Noise Level for most general use
• Static load rating of 3450 newtons and dynamic load rating of 8100 newtons

• It is durable
• Easy to use
• Use as directed

• Specifications: Hardness: 58-60HRC; Number of Teeth: 12; Outside Diameter: 53mm / 2.09-inch; Total Width: 7mm / 0.28-inch; Bore Diameter: 12mm / 0.47-inch; Pitch: 1/2-inch / 12.7mm; Tooth Width: 7mm / 0.28-inch; 1 x Chain Sprocket
• Chain Sprockets are normally mounted in a fixed position on a fixed shaft. This type A chain sprocket has no hub extension either side. Suitable for short shaft fixing.
• The chain sprocket should not rotate at a greater speed than is allowable for drive sprockets of the same size. Every roller chain sprocket comes with strong teeth that can latch onto the chain. It is suggested that chain sprockets have at least three teeth in mesh with the chain.
• The product is made of A3 carbon steel. High-frequency quenching treatment of teeth, the surface hardness, wear resistance are significantly improved. The part without quenching retains the original toughness and is easy to further process. It can be processed into different inner diameter sizes according to the requirements of use.
• There is no anti-rust coating on the surface of the product, and there may be rust on the surface, which does not affect the use. You can use sandpaper to remove the rust before use.

• [Size] - 16mm Outside Diameter, 14mm Inner Diameter, 1mm Cross-Section Diameter
• [Hardness] - 50 Durometer (Shore Hardness) for resistance to penetration
• [VMQ] - Standard silicone with a wide temperature range from -22? (-30??) to 392? (200??)
• [Application] - Can be used for travel mug cup lids, espresso coffee maker and weldless fitting for brewing
• [Application] - Widely used for Hydraulics and Pneumatics sealing, pressure valve, gas compressor, reaction valve, heat exchanger, boiler, filter, mechanical

• 4mm in diameter
• Made of High Precision Brass (H62)
• Smooth surface precision balls. Lightly lubricated
• Good hardness and corrosion resistance
• Package includes 100 piece balls

• [Size] - 20mm Outside Diameter, 14mm Inner Diameter, 3mm Cross-Section Diameter
• [Hardness] - 70A Durometer (Shore Hardness) for resistance to penetration
• [Buna-N] - Standard Nitrile Butadiene Rubber with a wide temperature range from -4? (-20 degreeC) to 212? (100 degreeC)
• [Application] - Widely used for pressure washer, filter, pump, water hose, plumbing pipe, garage maintenance, automobile mechanical and much more
• [NOTE] - Please confirm the required size and material before purchase, and put it in the right place

• Specification: Outer Diameter: 3mm/0.12\";Wire Diameter: 0.4mm/0.01\";Total Length: 40mm/1.56\"
• Material: 304 Stainless steel wire offers good mechanical properties with greater corrosion and heat resistance than music wire.
• Application: Compression spring steel wire spring is used for everything from home appliances to motor equipment, toys, lawn mowers, etc.
• How to use: It can be directly put on the rod products or put into the tube products.
• Package Content: 10Pcs x Compression Spring

• Deep Groove Ball Bearing
• Double Sealed
• Good quality product

• Specification: Outer Diameter: 4mm/0.16\";Wire Diameter: 0.4mm/0.01\";Total Length: 20mm/0.78\"
• Material: 304 Stainless steel wire offers good mechanical properties with greater corrosion and heat resistance than music wire.
• Application: Compression spring steel wire spring is used for everything from home appliances to motor equipment, toys, lawn mowers, etc.
• How to use: It can be directly put on the rod products or put into the tube products.
• Package Content: 10Pcs x Compression Spring

• [MODLE] - Bearing Model: AXK0819 (I.D.=8mm, O.D.=19mm, Thickness=2mm); Washer Model: AS0819
• [MATERIAL] - Chromium steel rollers for heat tolerance and durability under heavy loads; Steel cage guides and evenly spaced rollers for reduced friction, vibration, and noise
• [FEATURES] - Needle Roller Thrust Bearings can accommodate axial loads in one direction only
• [WASHER] - Combined with 2 washers for applications where adjacent machine components cannot serve as raceways
• [CAPABILITY] - 17.2kN Static Load Capacity, 7.25kN Dynamic Load Capacity, 15500RPM Maximum Rotational Speed