Robotics By Generic

• Maximum motor supply current: 2A per motor.
• Current Sense for each motor.
• Heatsink for better performance.
• Power-On LED indicator.
• Double H bridge Drive Chip: L298N.

• The Vibration module based on the vibration sensor SW-420 and Comparator LM393 to detect if there is any vibration that beyond the threshold.
• The threshold can be adjusted by the on-board potentiometer. When this no vibration, this module output logic LOW the signal indicate LED light,And vice versa.
• Uses: For a variety of shocks triggering, theft alarm, smart car, an earthquake alarm, motorcycle alarm. This module when compared with normally open penumatic shock sensor module, shock triggered much longer can drive relay module Module features: the use of the company's production of SW-420 normally closed type vibration sensors.

• Contact Material: Tin Plated Phosphor Bronze; Connector: Male
• Current rating: 3A; Voltage rating: 150V
• Contact Resistance: <30 M; Wire Gauge Accepts: 22 ~ 28 AWG
• Pitch: 2.54mm
• Packaged by:- Sharvi Technologies (OPC) Pvt. Ltd.; Address:- #09, CK Nagar, AECS layout, Hosa Road, Bangalore-560100

• Model: AM2302
• Operating Voltage: 3 - 5.5V, Humidity measurement precision: ?2%RH
• Accuracy resolution: 0.1%, High precision, Capacitive type
• Humidity range: 0-100%RH
• Temperature range: -40-80 degreeC, Temperature measurement precision: ?0.5 degreeC

• Driver chip: L298 dual H-bridge driver chip., Operates up to 35V DC Drive part of the peak current Io: 2A / Bridge
• Logical part of the terminal power supply range Vss :4.5V-5.5V Logical part of the operating current range: 0 ~ 36mA Maximum power consumption: 20W
• Heatsink for better performance. Power-On LED indicator.
• Over-Current Protection (A) Yes
• No. of Channels 2

• NPN TRANSISTOR 40V 600MA SOT23
• PackageTO-236-3, SC-59, SOT-23-3
• Collector Emitter Breakdown Voltage 40V
• Current- 600MA
• From Shelfkey

• Soldering Iron Stand provides a safe place to set your hot soldering iron, easy to assembly
• iron stand can effectively protect the iron from being ironed at high temperature or the iron tips dropping on the ground, ensure welding safety and protects the tip
• Solid metal chassis plate
• Save energy and maintain temperature of the iron.
• When welding, do not apply too much pressure, otherwise the tip will be damaged. As long as the tip can fully contact the solder joint, heat can be transferred

• LM358N
• LM358N Low Power Dual Op-Amp IC
• Package includes-1pcs
• Dual high Gain Amplifier Circuits.
• Audio amplifier design

• Convert mechanical force to electrical signal
• Resonance Frequency: 4.6 Khz +/- 0.5 Khz
• Resonance Impedance: 200 Ohms
• Capacitance: 20nF +/- 30% at 1 Khz

• Material: Acrylic
• Thickness: 2.8~3mm
• Inner Diameter: 16mm
• Mounting Hole: 3.4mm
• Color: Blue

• Current DC Forward (If) (Max):50mA ~ 100mA
• Mounting Type:Through Hole
• Package / Case:Radial
• Voltage Forward (Vf) (Typ):1.2V ~ 1.45V
• Wavelength:850nm ~ 940nm

• Working voltage range: Dc 45v- 20v current drain:<60ua voltage output: High/low level signal:33v ttl output detection distance: 3--7m(can be adjusted) detection range: <140 degree
• Delay time: 5-200s(can be adjusted, default 5s +-3 percent) blockade time: 25 s (default) trigger: L: Non-repeatable trigger h: Repeat trigger (default) work temperature:-20-+80 degreec trigger method: L unrepeatable trigger / h repeatable trigger dimension: 32cm x 24cm x 18cm (approx)
• Infrared sensor with control circuit board the sensitivity and holding time can be adjusted

• Model: TP-01 Material: Plastic
• Temperature range: -20?? ~ 500?? (less)
• Connector Type: K Type
• Interface Type: flat plug-in
• Accuracy : ?2.5%/0.75%

• Value: 100K ohm
• Wattage: 0.25W

• 40 pin
• Type: Male
• Size: 2.54 mm