International Power Adapters By KNACRO

• Waterproof and non-isolated 120W boost converter module for converting DC 12V 24V 36V (9-36V) to 12V .
• Input Voltage is 9-36V and output Voltage is12V, output current is 10A (rated working current)
• Over Voltage protection, over temperature protection, over current protection, and automatically recover after removing obstacles
• It has 95 percent converting efficiency and it is also dust-proof, Shockproof, suitable for all kinds of harsh environments<
• Its dynamic response speed is 5 percent 200US, please lower the power or enhance heat radiation when temperature over 45

• Input voltage: DC 6-60V.Output voltage: Load Linear.
• Input Current: require large than the motor operating current.Output Current: determine load size.
• Continuous current: 20A within.Maximum power: 1200W .Quiescent Current: 0.01ma.
• Speed type: modulated current.Speed mode: ON OFF linear potentiometer 270 degrees.
• Operating frequency: 15KHZ.Speed Percentage: support.

• Protection circuit board is the heart of battery pack, must to have to avoid battery pack from explosion, fire and damage
• It will protect battery pack from overcharging, over-discharging over-current and short circuit.
• With equilibrium function to keep each cell in balance and good service life
• Used for 4 series 12V LiFePO4 batteries, comes with 5P-250mm wires
• Choosing the correct protection board and applying it appropriately is vital to the longevity your batteries

• Protection circuit board is the heart of battery pack, must to have to avoid battery pack from explosion, fire and damage.
• It will protect battery pack from overcharging, over-discharging over-current and short circuit.
• With equilibrium function to keep each cell in balance and good service life
• Used for 4 series 12V LiFePO4 batteries, comes with 5P-250mm wires
• Choosing the correct protection board and applying it appropriately is vital to the longevity your batteries

• This is a perfect choice if you are in need of a rugged push button! These metal push buttons are a very tough, small, panel-mount latching switch with an illuminated Blue LED Ring .
• It is a SPDT with 16mm threading and 1mm pitch. This button is perfect for basic On/Off functions with cable length 1M / 3.3ft
• These latched buttons are rated up to 5A and 250V AC while the LED is rated for 3-6V.
• Momentary switch: Push & Hold,ON; Release,OFF
• Works well with the pc and any device that requires a momentary 3-6V pulse to initiate on/off functions

• CH340T master chip, high-speed stability, the limit speed 1Mbps (921600bps)
• Optocoupler isolation program, high speed, low error, ultra stable.
• The use of original lengthened isolation power supply, the greater the spacing, better isolation, higher pressure.
• Output TX RX integrated protection diode to improve the impact resistance.
• USB end and serial output without any electrical connection, the full protection of the computer USB port will not be due to external short circuit, shock and other damage. To avoid interference caused by the computer crash, communication instability.

• Voltage to current module, can 0-2.5V / 3.3V / 5V 10V / 15V / 24V voltage conversion to 0-20mA / 4-20MA current signal output, by adjusting the voltage to adjust the size of the current. The module is small and easy to use in different places.
• Using single-chip embedded technology.
• Implement the industry standard voltage (0-2.5V / 3.3V / 5V 10V / 15V / 24V) into an industry standard current (0-10mA, 4-20mA).Drive capability MAX15mA, linear output, the output signal can be directly connected to the AD converter, with the AD function with the microcontroller connection.
• Easy to operate, can be fine-tuned by potentiometer.

• Module using genuine quality relay, normally open interfaces Maximum load: AC 250V / 10A, DC 30V / 10A;
• SMD optocoupler isolation, driving ability, stable performance; trigger current 5mA;
• Module voltage 12V; the module can be set high or low-level triggered by a jumper;
  Fault-tolerant design, even if the control line is broken, the relay will not operate; the power indicator (green), relay state indicator (red);
• User-friendly interface design, all interfaces can connect directly through the terminal leads, very convenient.

• WIDE APPLICATION: KNACRO relay module can be used in timing, delaying, cycle timing, intermittent timing, raft fishing machine, slow-down machine DIY, etc.
• DUAL DIGITAL TIME DISPLAY: Our digital delay is equipped with dual time display in two different color, clear and convenient for you to check and change the setting.
• WIDE TIMING RANGE: KNACRO time relay delay is able to tolerate the widest timing adjusting range: 0-999S/ 0-999M/ 0-999H, available for various application.
• SIMPLE WIRING & OPERATION: This relay switch is four-terminal wiring and setting by buttons, easy and simple for everyone to use it.
• AUTO STORE FUNCTION: This 12V time delay relay can store the setting automatically. Please wait 6 seconds after finishing setting the data. The data set will be stored automatically after 6 seconds.