Additive Manufacturing Products By Micro-Swiss

• Fits: Ender 5 / Ender 5 Pro / Ender 5 Plus
• 3:1 Gear ratio
• Adaptable to wide range of 3D Printers
• Seamless integration with Revo Hotend (24V)
• Made in USA by Micro Swiss

• Fits: CR-10 / CR-10s / Ender 3 / Ender 3 Pro / Ender 3 V2 / Sunlu S8 / Sunlu S8 Pro
• 3:1 Gear ratio
• Adaptable to wide range of 3D Printers
• Seamless integration with Revo Hotend (24V)
• Made in USA by Micro Swiss

• Fits: Ender 6 (Not compatible with BL-Touch)
• 3:1 Gear ratio
• Adaptable to wide range of 3D Printers
• Integrated with a Micro Swiss All Metal Hotend
• Made in USA by Micro Swiss

• Fits: Creality CR-10 V2 / Creality CR-10 V3
• 3:1 Gear ratio
• Adaptable to wide range of 3D Printers
• Integrated with a Micro Swiss All Metal Hotend
• Made in USA by Microswiss

• Drop in Direct Drive Extruder for CR-10 and Ender 3 Series. It is Fully Compatible with Creality CR-10 / CR-10s / Ender 3 / Ender 3 Pro / Ender 3 V2
• High Torque: 3:1 Gear ratio
• This kit comes with everything you need to upgrade your printer to a Direct Drive Extruder. It comes with 1x Master Extruder Assembly 1x Adaptation plate 1x Stepper motor 1x Fan Shroud 1x Custom extension cable 1x Hotend assembly and hardware kit.
• This extruder overcomes the shortcomings of all current counterparts on the market, to create an optimal printing experience for everyone. With the Bevel Gear design, we are able to achieve the industry shortest filament path (less than 41mm). The unique motor placement allows for highly compact, low overhang design. This further increases system rigidity.
• Made in USA by Microswiss

• Fits: Ender 5 / Ender 5 Pro / Ender 5 Plus
• Orifice size: .4mm
• Filament size: 1.75mm
• Made in USA by Micro Swiss

• Leak-Proof Nozzle: Tired of messy nozzle leaks that ruin your prints and waste filament FlowTech Hotend combines nozzle and thermal break into one permanently sealed assembly that ensures a leak-proof hotend.
• Cold Nozzle Change: Swapping out nozzles used to be a time-consuming and potentially hazardous task. With a FlowTech Hotend, nozzle changes are effortless, and there's no need for hot tightening, and you can do it with just one hand.
• High-Flow Characteristics: Ceramic cylindrical heater and 28.6mm melt zone provides excellent volumetric flow rate.
• All-Metal Design: Built to last! FlowTech hotend features an all-metal design that can handle most modern 3D printing filaments. The entire hotend is machined and assembled in-house, with quality control performed at multiple stages during the manufacturing process. At the end, each hotend undergoes a full thermal cycling test before it is packaged.
• Made in USA by Microswiss

• This is Micro Swiss All Metal Hotend Kit for Wanhao Duplicator 6 with the following improvements:
• Slot clamping system
• No screw to the thing and damage the thermal pipe
• Significantly better heat transfer (this is a big one!)
• Easier to disassemble and adjust. Precise control of the bore diameter

• Fits: Bowden extruder machines, Fits NEMA 17 size stepper motors
• Fits: Ender 3, 5, 6, CR10, CR-10s Pro, CR-10S, CR6-SE, Tornado
• Made in USA by Microswiss

• This is Micro Swiss All Metal Hot end kit with redesigned cooling block for Wenham i3, Wenham i3 Plus and all other i3 clones with the following improvements:
• Slotted Clamping system
• No set screw to ding and damage thermal tube
• Significantly better heat transfer (this is a big one!!!)
• Easier disassemble and adjustments

• Fits: Micro Swiss MK10 All Metal Hotend Kit ONLY (M7 Threads)
• A2 Hardened Tool Steel Plated with TwinClad XT
• WEAR RESISTANT
• Orifice size: .8mm
• Made in USA by Micro Swiss

• Fits: Ender 5 / Ender 5 Pro / Ender 5 Plus
• 3:1 Gear ratio
• Adaptable to wide range of 3D Printers
• Seamless integration with Revo Hotend (24V)
• Made in USA by Micro Swiss

• Fits: CR-10 / CR-10s / Ender 3 / Ender 3 Pro / Ender 3 V2 / Sunlu S8 / Sunlu S8 Pro
• 3:1 Gear ratio
• Adaptable to wide range of 3D Printers
• Seamless integration with Revo Hotend (24V)
• Made in USA by Micro Swiss

• Fits: Ender 6 (Not compatible with BL-Touch)
• 3:1 Gear ratio
• Adaptable to wide range of 3D Printers
• Integrated with a Micro Swiss All Metal Hotend
• Made in USA by Micro Swiss

• Fits: Creality CR-10 V2 / Creality CR-10 V3
• 3:1 Gear ratio
• Adaptable to wide range of 3D Printers
• Integrated with a Micro Swiss All Metal Hotend
• Made in USA by Microswiss