Fasteners By Newport Fasteners

• Thread: Coarse / Full Thread / Alloy Steel / Black Oxide
• Recommended Hex Socket Allen Key Wrench: Inch
• Black Oxide is not a protective finish and will rust if exposed to moisture. Stainless Steel material is recommended for environments with moisture

• Diameter - Thread Pitch: M12 - 1.75 / Length from Under Head: 200MM
• Coarse Thread / Partially Threaded
• 18-8 Stainless steel hex cap screws offer protection from weather and corrosive environments
• Rust resistant in fresh water environments, for salt water environments use the 316 stainless steel version
• Called hex cap bolts or hex cap screws

• DIN 933
• Coarse Thread
• Fully Threaded
• Tensile Strength: 800 N/mm2 (thru 16 mm diam.) 800 N/mm2 (over 16 mm diam.)
• Class 8.8 Steel, Quenched and Tempered

• Thread: Coarse / Partial Thread / Alloy Steel /
• Recommended Hex Socket Allen Key Wrench: 7/32 Inch
• Black Oxide is not a protective finish and will rust if exposed to moisture. Stainless Steel material is recommended for environments with moisture

• Diameter - Thread Pitch: 1/2\" - 13 / Length from Under Head: 1-1/4 Inch
• Coarse Thread / Fully Threaded
• 18-8 Stainless steel hex cap screws offer protection from weather and corrosive environments
• Rust resistant in fresh water environments, for salt water environments use the 316 stainless steel version
• Called hex cap bolts or hex cap screws

• Coarse Thread / Full Thread / 18-8 Stainless Steel
• Recommended Hex Socket Allen Key Wrench: 5/16 Inch

• DIN 961
• Fine Thread
• Fully Threaded
• Tensile Strength: 800 N/mm2 (thru 16 mm diam.) 800 N/mm2 (over 16 mm diam.)
• Class 8.8 Steel, Quenched and Tempered

• Diameter - Thread Pitch: M10 - 1.50 / Length from Under Head: 16MM
• Coarse Thread / Fully Threaded
• 18-8 Stainless steel hex cap screws offer protection from weather and corrosive environments
• Rust resistant in fresh water environments, for salt water environments use the 316 stainless steel version
• Called hex cap bolts or hex cap screws

• DIN 931
• Coarse Thread
• Partially Threaded
• Tensile Strength: 800 N/mm2 (thru 16 mm diam.) 800 N/mm2 (over 16 mm diam.)
• Class 8.8 Steel, Quenched and Tempered

• ASME
• Coarse Thread
• Partially Threaded
• Tensile Strength: 800 N/mm2 (thru 16 mm diam.) 800 N/mm2 (over 16 mm diam.)
• Class 8.8 Steel, Quenched and Tempered

• HIGH QUALITY STAINLESS STEEL: These #10 Wood Screws (Drywall Screws) are high quality grade Marine Grade Type 316 Stainless Steel, giving the screws one of the highest forms of corrosion resistance and strength, making it last longer than other hardware on the market today.
• Type 316 steel is an austenitic chromium-nickelstainless steel that contains between two and three percent molybdenum. The molybdenum content increases corrosion resistance, improves resistance to pitting in chloride ion solutions and increases strength at high temperatures. Type 316 Stainless is more resistant to corrosion than 18-8 stainless but not as strong. Ideal for Salt Water envirovments or chemical exposure environments.
• Type 17 Point - This thread cutting screw is ideal for use with wood; it offers a coarse tapping screw thread as well as a special long sharp point that is fluted in order to capture chips. The patented thread design and Type 17 point make drilling faster, reduce splitting, and allow these screws to be driven into most hardwoods without pre-drilling
• Features a Bugle Head, and a Square drive to be used with a #2 Square Drive
• Size Number: #10 / Length of Screw is 3-1/2\" inches with 2-1/4\" inches of thread

• Manufactured to ASME B18.5 Specifications

• DIN 933
• Grade 8.8 Steel
• Coarse Thread / Fully Threaded
• Tensile Strength: 800 N/mm2 (thru 16 mm diam.) 800 N/mm2 (over 16 mm diam.)
• Class 8.8 Steel, Quenched and Tempered

• DIN 931
• Grade 8.8 Steel
• Coarse Thread / Partially Threaded 22mm inches of Thread
• Tensile Strength: 800 N/mm2 (thru 16 mm diam.) 800 N/mm2 (over 16 mm diam.)
• Class 8.8 Steel, Quenched and Tempered

• DIN 931
• Grade 8.8 Steel
• Coarse Thread / Partially Threaded 30mm inches of Thread
• Tensile Strength: 800 N/mm2 (thru 16 mm diam.) 800 N/mm2 (over 16 mm diam.)
• Class 8.8 Steel, Quenched and Tempered

• Diameter-Threads Per Inch: 7/16-14
• Length: 1-3/4 inch
• Grade 5 bolts for moderate stress applications. Stronger than Grade 2 bolts but not as strong as Grade 8 bolts