Fasteners By SIMPSON

• Thread design undercuts to efficiently transfer the load to the base material; qualified for static and seismic loading conditions
• Specialized heat-treating process creates tip Hardness for better cutting without compromising the ductility
• No special drill bit required - designed to install using standard-sized ANSI tolerance drill Bits
• Hex-washer head requires no separate washer, unless required by Code, and provides a clean installed appearance
• Cost-effective solution for less extreme applications where the environment may be wet, moist or damp

• One piece wrap around clip
• Threaded end is chamfered for ease of starting Nut
• Most sizes feature full Thread for added versatility

• Thread design undercuts to efficiently transfer the load to the base material; qualified for static and seismic loading conditions
• Specialized heat-treating process creates tip Hardness for better cutting without compromising the ductility
• No special drill bit required - designed to install using standard-sized ANSI tolerance drill Bits
• Hex-washer head requires no separate washer, unless required by Code, and provides a clean installed appearance
• Ideal for applications in corrosive or extreme environments such as salt water or when chemical/corrosive solutions are present

• Finished in Simpson Strong-Tie gray paint
• Top flange-3 gauge; Stirrups-7 gauge
• HGLTV hangers should not be attached to nailer's

• Patented EB-GUIDE predrill guide provides precise fastener angle alignment for consistent biscuit installations. Stainless-steel reinforced biscuit provides strength and increased pullover resistance
• Underside keel provides consistent fastener positioning. Radius sides and chamfered edges provide easier alignment and faster installation
• Type 316 stainless-steel trim-head, 6-lobe screws with black-painted heads provide a concealed finish and blend in with EB-TY biscuit. Decking thickness: 3/4 in.
• Spacing requirement: 1/4 in. EB332WP, EB14WP, EB316WP series with 1-5/8 in. screws are designed for roof decks installed on 1 in. sleepers
• Includes: EB-TY Premium biscuits, stainless-steel screws, Ip? plugs for first and last board installations, EB-GUIDE predrilling tool, 1/8 in. quick-release impact-ready drill bit, T-15 6-lobe driver bit for reduced cam outs. Quantity: 175

• Installed easily by a single Installer
• Many applications require only one screw
• Tested to include stud-web strength and stiffness in the tabulated design values
• Flexible design solutions for web thicknesses of 33 mil (20 ga.) through 97 mil (12 ga.)
• Compact profile allows standard 1 5/8 inch studs to be sistered directly against adjacent studs

• Use with 10-10d Nails
• Made from 7-gauge steel
• Steel column caps provide adequate bearing length for larger girder reactions

• BP1/2-R
• 1/2 in. Bearing Plate
• Greater Bearing Surface Than Standard Cut Washers
• Designed To Help Strengthen Plate Connections
• Help Distribute The Load At These Critical Connections

• Attach brick veneer to the supporting wooden framing of the walls
• Typically for use on the outside of structures
• Embossments provide extra holding power
• Made from 22 gauge steel
• Galvanized for extra corrosion resistance

• One piece wrap around clip
• Threaded end is chamfered for ease of starting Nut
• Most sizes feature full Thread for added versatility

• Pancake head, type-17 point
• #2 square drive (driver bit in each box; replacement bit model BIT2SU)
• Straight collation

• Uses 5/8-inch Bolts
• Made from 7-gauge steel
• 4x Beam Width
• Diamond holes are included to provide for temporary fastening
• Assembled with certified welds for confidence in strength and loading

• Column caps provide a high-capacity connection for column-beam combinations
• Bolt holes shall be a minimum of 1/32 inch to a maximum of 1/16 inch larger than the bolt diameter
• Quantity: 1 each