Industrial & Scientific Store - Robotics

• Compatibility This 170 tie points (17 x 5 x 2 points) breadboard is compatible to prototype DIP IC's, resistors, diodes, transistors, leds, capacitors pots and other types of electronic components
• Easy wiring With tight plug-in contacts, the components will sit well after assembly, no wobbles. Jumper wires are easy to insert into or remove from these breadboards
• Durability Mini breadboard is made of ABS plastic, and the internal contacts material is made of tin-phosphor bronze, have good abrasion resistance and corrosion resistance
• Reusable The solderless breadboards do not require soldering, can be reusable. suitable for the prototypes and circuit design experiment teaching and other DIY projects, matching jumper
• Package Contents: 5 x BreadBoard

• Bigger current, high torque,, forward backward direction
• You can adjust the speed of the motor and the direction of rotation. The maximum current of this regulator is 40A.
• Power requirement: DC 9-50 V / wide operating voltage range
• Control power: 0.01-2000W (maximum rated current 40A, long operating current up to 20A)
• Direction control: Rocker switch, \"I\" is forward / CW, \"II\" is reverse / CCW and \"0\" is STOP / brake

• High Print Resolution & Easy Heat Transfer
• For use with LASER printers only
• Comfortable A4 size paper
• NOTE - THIS PAPER IS FOR MAKING PRINTED CIRCUIT BOARDS, THIS PAPER IS NOT FOR T-SHIRT PRINTING.

• SS 304 pipe to protect against harsh environments
• Total pipe length 12 inch - Pipe diameter(ø) 3/8 inch
• Teflon wire for connect with element
• Connection head Aluminum cast head with captive gasket
• Package Content: ATC RTD type PT-100 ()ohm Temperature Sensor 3 wire (Temperature controller)

• Value: 180 ohm
• Wattage: 0.25W

• high speed DC motor for DC or solar fan
• high speed DC motor for DC or solar cooler
• 12 Volts DC Motor
• Big Torque Motor
• Copper Winding
• High Speed RPM Motor

• Inclusions Solder Wire
• Power Requirements: Corded, 25 W
• Maximum Temperature: 250 degree C
• Pack of 2

• Mechanical Tool

• 100 % SATISFACTION GUARANTED Excellent quality and an empty canvas for electrical enthusiasts! An easy soldering; 0.1\" hole spacing for DIP integrated circuits and headers.
• THIS IS NOT YOUR NORMAL PERF BOARD! This board is much higher quality with plated-through-holes and annular rings that will not lift off the PCB under normal soldering conditions
• MUTI-PURPOSE General purpose prototyping circuit board for analog and digital use; With pre-tinned plated holes; Double sided board with plated-thru holes allows components to be easily soldered to either side of the board
• THE FLEXIBILITY OF HAVING CHOICES Great assortment with variety of size and perfect for quickly prototyping stackable circuits
• PACKAGE COMPONENT 40 Piece of double sided PCB prototype board in 5 different size (2x8 and 3x7 each 10 Pcs; 4x6 and 5x7 each 8 Pcs; 7x9 cm each 4 Pcs) with mounting holes or slots on each board corner

• Cost-effectiveness
• Resistance to corrosion
• High strength-to-weight ratio
• Variety of size and shapes
• Variety of size and shapes

• Operating Voltage: 5V DC
• High sensitivity to LPG, natural gas, town gas.
• Small sensitivity to alcohol, smoke.
• Simple drive circuit.
• Fast response.

• Protect your home and valuables from a fire due to a Lipo battery failure with this Lipo-Safe bag
• Useful for storage, travel and during charging. The bag has an inner lining made from a woven fire retardant fiberglass material, which helps contain and greatly reduce any fires inside the bag.
• Silver tone oxford Material lipo battery safe guard charging protection waterproof bag pouch for rc model.
• Warning:never leave charging battery unattended.Allways ensure the battery is on a non-flammable surface.
• Product Name : RC Protection Bag;Fit for : RC Model Lipo Battery Size : 310 x 230mm/ 11.4\" x 9\"(L*W);Material : Oxford Material, Nylon Color : Silver Tone Weight : 118g Package : 1 x RC Protection Bag

• Single direction thrust ball bearings consist of a shaft washer, a housing washer and a ball and cage thrust assembly. The bearings are separable so that mounting is simple as the washers and the ball and cage assembly can be mounted separately
• Bearing ID: 12mm, OD: 26mm; Height: 9mm
• Single direction thrust ball bearings, as their name suggests, can accommodate axial loads in one direction and thus locate a shaft axially in one direction. They must not be subjected to any radial load.
• Basic load ratings: Dynamic: 10.4 kN, Static: 15.4 kN; Speed ratings: Reference speed: 6700 r/min, Limiting speed 10000 r/min
• Package include: 2 x 51101 Axial Thrust Bearing

• For fast iot prototyping
• It is flashed with the nodemcu firmware and can be set up and programmed right away with the on-board microusb connection
• The d1 mini is a mini wifi board based on esp-8266ex

• PCB size:1.52cm x 2.22cm Working Voltage: 5 Volt DC Output: 4-5 Volt DC
• On detecting a laser signal, output goes at high level (5V) until laser signal is there. NOTE: This sensor is non-modulator, to be used indoors away from any bright light or direct sunlight.

• Best in market for remote operation of motor using mobile in 3 different modes(Timer, Scheduler & Manual)
• 4G supported device
• Device can be operated through Mobile Application & SMS
• For every operation (like ON, OFF, Power Loss, Dry Run etc.) acknowledgment messages will be sent
• Safeguards motor from voltage fluctuations and Dry Run
• Transaction history can be viewed in mobile application
• Complete Automation and remote management to eliminate labour and save time