Water Level Controller By KREENA TECHNOLOGIES

• Warranty :18 MONTH Manufacturer. Warranty Service : Repair or Replacement.
• THIS MODEL IS SUITABLE TO ANY 3 PHASE STARTER PANEL
• FULLY AUTOMATIC AUTO OFF WHEN TANK IS FULL OR SUMP IS EMPTY
• Suitable to any HP Motor as no load comes on our controller. Load passes to existing starter.
• Auto and Manual mode switch available, Sensor fault detection provided, if sensor got failed LED start blinking

• Fully Automatic Controller, Micro Controller Based Design, Power Failure protection. (Not Start Motor Every Time on Power Failure. )
• When the water level in the tank becomes low, means water get down from middle sensor, motor get switch on automatically. The tank starts filling up. When the water level reaches to the higher level, the top level sensor sense. the motor automatically gets switched off
• Package Contain : 1 Water Level Controller Unit. 3 no S.S Sensors. 1 user manual with technical details
• Suitable to 0.1 HP to 2.0 HP Motor
• Auto and manual switch available

• Warranty : 1 Year Manufacturer. Warranty Service : Repair or Replacement. Package Contain : 1 Water Level Controller Unit. 6 SS Sensors. 1 user manual with technical details.
• High quality M.S. Enclosure. Microcontroller based water level controller, all signal will pass in sensor through AC filter circuit that provides filter signal to sensor, that improve life of sensor, A.C signal passes on sensor side so never get rusting problem.
• This model automatically switch ON and switch OFF Motor. When water level of overhead tank becomes low means water get down from middle sensor and water is present in the underground tank or sump, motor get start automatically. The tank starts filling up. when the water level reaches to the higher level, the motor automatically gets switched off. AUTO OFF WHEN TANK IS FULL OR SUMP IS EMPTY.
• This model have dry run protection so it only start motor if water present in underground tank or sump. Suitable for 0.1 HP to 5.0 HP Motor, Protect motor from dry running. Motor ON OFF LED indication provided. Water Level indication provided for both tank. Supply voltage : 220-270 V AC, Sensing element : 304 S.S Sensor it is free from oxidation, long life. Any conducting wire can be use for sensor.
• Auto and Manual mode switch available. In auto mode motor start and stop automatically. In manual mode user can start and stop motor by pressing start and stop button of controller. No additional wiring require to operate motor manually. Also Suitable for MCB Starter panel and submersible motor, see diagram above for connection. High quality M.S. enclosure provided. Fully automatic, controls from underground tank to overhead tank so no man power required. Long service Life.

• Warranty : 18 Month Manufacturer. Warranty Service : Repair or Replacement. Package Contain : 1 Water Level Controller Unit. 6 S.S Sensors. 1 user manual with technical details.
• When the water level of the overhead tank becomes low means water gets down from the middle sensor and water is present in the underground tank or sump, the motor gets started automatically. The tank starts filling up. when the water level reaches to the higher level, the motor automatically gets switched off.
• AUTO OFF WHEN TANK IS FULL OR SUMP IS EMPTY.
• Sensor fault detection provided, if sensor got failed LED start blinking
• Auto and Manual mode switch available

• THIS IS MODEL IS COMBINATION OF MOTOR STARTER AND WATER LEVER CONTROLLER Microcontroller based water level controller, all signal will pass in sensor through AC filter circuit that provides filter signal to sensor, that improve life of sensor, Digital display for voltage and ampere high low voltage protection overload protection with spp
• When water level of overhead tank becomes low means water get down from middle sensor and water is present in the underground tank or sump, motor get start automatically. The tank starts filling up. when the water level reaches to the higher level, the motor automatically gets switched off. AUTO OFF WHEN TANK IS FULL OR SUMP IS EMPTY. This model have dry run protection so it only start motor if water present in underground tank or sump
• Suitable for 0.1 HP to 7.5 HP Motor, It protect motor from phase failure. It protect motor from phase interchange. It protect motor from voltage different between 3 phase
• high voltage protection, low voltage protection, Short circuit protection overload protection Adjustable overload from 4 A to 20 A RESET button provided to reset unit Start and stop button provided high voltage indication low voltage indication overload indication Power indication provided Input Voltage : 415 VAC Output Voltage : 415 VAC
• It has current based dry running. If motor runs without water then it take lower current then its actual current. so when motor current get down from its actual current, it stop motor and protect motor from dry running

• Warranty : 18 MONTH Manufacturer. Warranty Service : Repair or Replacement.
• When water comes in the municiple line, it will start the motor
• AUTO OFF WHEN NO WATER IN T SENSOR.
• Suitable for 0.1 HP to 1.5 HP Motor,
• Auto and Manual mode switch available

• Warranty : 18 month Manufacturer. Warranty Service : Repair or Replacement. Package Contain : 1 Digital Starter with water level controller 6 S.S sensors 1 user manual
• This model is the combination of a digital water level controller and motor control panel (motor starter).
• Overload Protection, High & Low Voltage protection, Current based dry run protection Digital Volt and ampere meter are provided to see system voltage and load current accordingly
• Cyclic timer Delay timer provided with bypass facility Dry run Auto Reset timer provided with with bypass facility
• Auto swtich (when power goes and comes it start automatically) provided with bypass facility SPP ProvidedAUTO OFF WHEN TANK IS FULL OR SUMP IS EMPTY.

• Fully Automatic Controller, Micro Controller Based Design, Power Failure protection. (Not Start Motor Every Time on Power Failure. )
• When the water level in the tank becomes low, means water get down from middle sensor, motor get switch on automatically. The tank starts filling up. When the water level reaches to the higher level, the top level sensor sense. the motor automatically gets switched off
• Package Contain : 1 Water Level Controller Unit. 3 no S.S Sensors. 1 user manual with technical details
• Suitable to 0.1 HP to 2.0 HP Motor
• Auto and manual switch available

• Working : As shown in the diagram out of three sensors, 1 sensor put at the bottom, 1 sensor put at middle, and 1 sensor at top level of the tank. When the water level in the tank becomes low, means water get down from middle sensor, motor get switch on automatically. The tank starts filling up. When the water level reaches to the higher level, the top level sensor sense. the motor automatically gets switched off
• Warranty : 1 Year Manufacturer. Warranty Service : Repair or Replacement. Package Contain : 1 Water Level Controller Unit. 3 no S.S Sensors. 1 user manual with technical details
• Water level indication provided to see water level in tank. Motor ON OFF indication provided. High quality ABS Enclosure. No man power is required as it is operate as fully automatic. Supply voltage : 220-270 V AC, Suitable to 0.1 HP to 2.0 HP Motor. Also suitable for single phase MCB starter panel and submersible motor
• Auto and manual switch available. In auto mode, motor start and stop automatically. In manual model, motor start and stop with manual switch, No additional wiring require to operate motor in manual. Sensing Elements: S.S sensors, it is free from oxidation. Long life. Any conducting wire can be use for sensor