Water Treatments - Water Level Controller

• 2 Years Warranty
• LCD Display
• High Voltage Protection
• Low Voltage Protection
• Over Load Protection
• Dry Run Protection
• Manual Mode
• Auto ON/OFF

• 6 Months Warranty.
• Physical Damage Not Included
• Compatible with most of water level indicators and controllers

• VENEX ELECTRICALS semi automatic water level controller for single phase motor up to 1 hp
• load capicity 10 AMP
• customer care 9898111264
• manual start and auto stop function
• with 2 ss sensor,level indicator, motor on indicator,supply indicator

• Environmentally friendly
• FLOAT mayerial- POLYPROPYLENE PERFECTLY SEALED FEATURES DOES NOT ALLOW WATER TO ENTER FLOAT
• Water Level, liquid level Controller

• Suitable for all types of Single Phase Pumps
• Motor Wattage : 20A@230V
• Easy To install And Use
• Small And Compact In Size
• Timing Range : 5 Min To 30 Min

• (easy install) only with 1 hole
• no need plumber and electrician
• multi size adjustable
• long lasting

• Low Voltage ( 130V), High Voltage (270V) & Overload Protection. [With Amp. Adjustable Knob]
• Inbuilt water level Upper and lower bath tank control
• Both tank empty & feeling LED indications
• Auto and manual slide switch.
• Why & What Is Run Capacitor? :- The Run Capacitor Is Inbuilt Provided In The Device. The Run Capacitor Provides Support To The Motor During Its Running Or Operational time And This Run Capacitor Is of 50.mfd, Therefore, It Can Operate on upto 1.0 To 1.5 Hp. Motor

• Material,Color,Green
• Shape,square
• One piece of water level controller PCB board for motor operated by switch/MCB for overhead tank with three sensors
• Item Size 6*6*4 cm
• Condition New

• 3 Phase Water Level controller
• Electrolysis Free
• Corrosion less Water Level Controller
• Stainless Still Sensor
• 3 Phase D.O.L And Fully Star Delta Motor Supported

• Single Phase Digital Fully Automatic Water Level Controller For Municipality Water With All Types Of Protection
• Digital Display For Displaying Voltage And Ampere And Fault Of Your Motor
• Just Get This Product And Get Free From Headache Of Check And Start Motor At the Time Of Municipality Water Timing, As It Will Start The Motor Automatic By Detecting Municipality Water At Inlet Of The Motor
• Operating Voltage:-230 Volt and Support Up To 20 amps

• Motcon V2 uses microcontroller based intelligent circuit
• Overhead tank/ Sump water level sensing
• The system uses 16*2 LCD Display as graphical user interface
• The pump set will be swiched OFF, if the system detects dry run situations due to pump set or plumping problem and will give audible alarm
• The pump set does not turn ON at high/low voltage

• SS-316 pins are used in it to avoid the rust and chemical resistant.
• SS pin moulded within Polypropylene.
• Completely insulated wire joints.
• Cable Length: 1 Meters.
• Physical Damage Not Included.

• Specially Design for Submersible Pumps (Low Cost)
• Corrosion free magnetic float sensors
• Save Electricity, Save Water, Save Money, Save Time
• Guarantee:1 Year Manufacture. Guarantee Service : Repair/Replacement.
• Automatic water level controller is used to automatically fill the over head tank as and when it gets empty and monitor the water level in it. Automatic water level controller switches ON the motor when the water level in the overhead tank drops below prefixed low level (on point) and puts off the motor when water level rises up to prefixed high level (off point). The system is very versatile.

• Normally Open Type
• Corrosion Free Material
• Advance Magnetic Technology
• Cable Length : 2 meter
• Max Switch Current : 5A (DC), Max Switch Watt : 10W / VA, Ideal Operating Ratings : Voltage: 2 to 12V DC Current: 5 to 50mA DC

• Cable: 3 Meter (customized wire length is available)/ A float switch is a device used to detect the level of liquid within a tank. The switch may be used in a pump, an indicator, an alarm, or other devices and Use: Water Level, liquid level Controller
• Rated voltage: 250V and Rated current: 8A/Contacts: NO+NC and Weight: 635 g
• Endurance: =500,000 times of wire and Plastic Body Electrical
• INSTRUCTIONS, for INSTALLATION Insert the cable in the counter weight (yellow color part), from the conical part and rotate it. Thus causing the plastic ring inserted in the opening to become detached (if necessary this operation can be facilitated with the use of a screwdriver). The ring should then be positioned in the point where it is desired to block the counterweight. Force the counterweight on the ring by rotating it using a slight pressure

• Low Voltage (Below 290V), High Voltage (Above 480V) & Overload Protection (as per inverse time current characteristics) & SPP (Single Phasing Protection).
• Inbuilt time delay system (Protection from suddenly high power when main supply resume)
• Indication for Motor ON, High / Low Voltage , Overload & both upper & lower tank level indications
• Auto mode available to easy controlling (Auto Fill and Auto Off features available)
• Inbuilt water level, Upper and lower both tank level control. & Variable Current (Amp) setting.