Additive Manufacturing Products By BIGTREETECH

• Why use EZ Drivers? Because 40% of users have damaged the driver due to the wrong installation. It will damage the control board or even more damage. Using EZ Drivers can improve the experience of more users
• SKR 3 EZ 3D Control Board adopts two kinds of driver sockets, which are compatible with both BIGTREETECH EZ series driver modules and TMC series driver modules. Each motor drive module can select the corresponding motor voltage through the jumper cap
• SKR 3 EZ mainboard using 32-bit ARM Cortex-M7 series STM32H723VGT6 main control chip with a main frequency of 480MHz, the performance has greatly improved. It reserves the BOOT button, users can update the motherboard boot program through DFU
• SKR 3 EZ's numerical control fan realizes 24V, 12V, 5V voltage selection through the external power supply module, eliminating the need for the operation of the customer's external transformer module, thereby reducing the probability of damage to the motherboard
• EZ Drivers can achieve quietness when the motor is locked and running at low speed. It is recommended to select when the maximum motor speed is lower than 300RPM; it can achieve quietness and low power consumption in a wide range of speed and torque. It is recommended that the maximum motor speed exceeds 300RPM Select at 300RPM

• 32-bit Control Chip: BIGTREETECH Octopus Pro V1.0.1 control board adopts 32-bit ARM-level Cortex-M4 series STM32F429ZGT6 chip with a frequency of 180MHz and 1MB of flash memory, support Klipper/Marlin/RRF and Raspberry Pi, Octoprint. Compatible with BTT Pi V1.2/Pi2, CB1/CB2+Pi4b adapter.
• 6 Controllable Fans: BIGTREETECH Octopus Pro V1.0.1 F429 board with up to 6 PWM fans and 2 always-on fans with the ability to individually select the voltage that will drive each fan. Select from Vin, 12V or 5V. Supports up to 4 hotend heaters. Flyback protection on PWN fan ports are effectively against short circuits in the fan sockets to prevent damages on fans
• 8 Axis: BTT Octopus Pro V1.0.1 3D printer control board provides space for up to 8 stepper drivers on Octopus Pro controller board in STEP/DIR, UART or SPI mode, TMC2209/TMC2208/TMC5160T Pro driver, which can control up to 8 different axes. It's especially suitable for multi-colour printing and tool changer. Added high voltage (HV) drivers support input voltage 12V-maximum 60V (only for the motor drive power supply).
• Widely Compatible: BIGTREETECH Octopus Pro V1.0.1 motherboard supports BTT TFT35/43/50/70, HDMI5 V1.2 touchscreen display, LCD2004 and LCD12864. Supports smart filament runout sensor, shutdown after printing, power loss print resume, CEB V1.0 CAN adapter board, SKSM V1.0 SBC Power Protection Module, Microprobe, Bltouch, Eddy auto bed leveling sensor
• Update firmware via DFU: Supports USB and DFU mode updates. Updating the firmware via DFU mode and allows us to upload firmware or bootloader in case the normal process does not work when using a USB-C cable. If have any question?please contact us in time and we will provider satisfactory solution

• Main Control Chip Features This new SKR Mini E3 V2.0 motherboard uses the STM32F103RET6 main control chip, and its flash memory size is 512K.
• CNC Fan Because the fan on the SKR Mini E3 V2.0 control board is a CNC fan, you need to set the wind speed before using it. (Note: V2.0 version of the fan is not ready to use after power on).
• TFT35 E3 V3.0 This display board has higher compatibility. Users can select two work modes:UART serial port screen mode and 12864 screen mode;Serial port screen mode supports two printing modes: SD card and U disk.
• MOSFET The hot bed MOS tube uses WSK220N04, low on-resistance, larger heat dissipation area, and reduce heat generation.
• After-sales Support If you encounter any problems, please write us via Amazon as soon as possible. We have professional technical after-sales personnel to solve your problems; Thank you for your support.

• If you encounter any problems, please write us via Amazon as soon as possible. We have professional technical after-sales personnel to solve your problems
• Because the fan on the SKR Mini E3 V2.0 control board is a CNC fan, you need to set the wind speed before using it. (Note: V2.0 version of the fan is not ready to use after power on)
• Compatible with BLTouch, RGB color lights, occlusion detection, stop and other functions
• Increase the distance between the driving chip and the components to avoid the trouble caused by the heat sink
• BLTouch is an auto leveling sensor for 3D Printers based on open-source.Simple, Smart, High-precision.It could work with any kinds of bed materials, such as glasses, woods, metals, and so on

• BIGTREETECH SKR V1.4 Turbo using 32-bit 120MHz ARM-class Cortex-M3 series LPC1769 main control chip, the performance is greatly improved.
• SKR V1.4 Turbo control board can supply power to TFT screen, BLtouch, Neo-pixel by plugging in an external DC5V power module; in addition, I2C, SPI, WIFI interface is reserved to facilitate customer DIY.
• On-board TMC-driven SPI working mode and UART working mode, and the on-board DIAG function pins are convenient for customers to use, eliminating the complicated wiring process, which can be used by simply removing and inserting the jumper cap.
• Compare to other stepper motor driver in the market, our TMC2209 silent stepper driver generate lower heat and it has a large-area cooling position to lower the temperature. It driver can lower 30% heat than others stepper motor drivers even working last for a long time. With Passive cooling on a 10 hours print, they only hit 37?.
• BIGTREETECH TMC2209 V1.3 is an ultra-silent motor driver IC for two-phase stepper motors, which adopts stealthChop2 Mute technology which reduces motor noise to the point of silence at low velocities to ensures noiseless operation, maximum efficiency and best motor torque. spreadCycle allow for highly dynamic motion. Drive current 2A, peak current 2.8A, voltage range 4.75V-29V, 256 subdivision.

• 32 Bit Microprocessor : Adopted ARM Cortex-M3 series STM32F207VCT6 master controller chip with 32-bit CPU main frequency of 120 MHz, BTT TFT35 V3.0.1 touch screen can perfectly replace the LCD12864 screen for use.
• Dual Working Modes : BTT TFT35 V3.0.1 display enables two different modes, with options for either LCD12864 Encoder Mode, or the modern Colour Touch Screen Style. It also supports both SD card and USB stick printing.
• More Reserved Extensions :TFT35 V3.0.1 touch screen reserves the extension ports of filament break detection, automatic shutdown after printing, also WIFI function can be realized by external WIFI module through WIFI port.
• Easy Firmware Updates : It is easy and convenient to update firmware by SD card, simply downloading from Github, coping and saving it to SD card. firmware must be reserved, then re-plug the SD card and wait to 10s. That's all takes to finish updating on firmware.
• 100% Technical Supports : If you have any problems about BTT TFT35 V3.0.1 touchscreen, please feel free to contact us on Amazon. Our technical supports team will respon to you within 24 hours. 1-Year Warranty is 100% guaranteed!

• The main control uses the ARM-level Cortex-M4 series with a 32-bit dominant frequency of 168 MHz STM32F407ZGT6 chip, performance is greatly improved
• Equipped with highly modular open source firmware Marlin2.0, it is convenient for users to DIY and further-development, to avoid the worry of not being able to master the core code
• Motor driver support :TMC2209, TMC2208, TMC5160, TMC2130, EZ2209, EZ5160, EZ2130, EZ2208, etc..Display screen support: BIGTREETECH TFT35-E3, TFT35, TFT50, TFT70, Mini12864, etc.
• Support Serial WIFI Online Printing. 6 motor drives, 3 extruders, 3 CNC fans. Reserve extended ports of BL Touch, PWM, ADC, UART, I2C and SPI; Support power-off continuous printing, material cut detection, shutdown and other functions; Support for dual Z axis printers
• If you encounter any problems, please contact us via Amazon as soon as possible. We have professional technical after-sales personnel to solve your problems

• Main Control Chip: Uses a 32-bit ARM Cortex-M4 series STM32F446ZET6 main control chip with a core frequency of 180MHz
• Strong DIY Support: This motherboard supports up to 8 stepper drivers with 9 stepper driver outputs in total; And up to 6 PWM fans and 2 always-on fans with the ability to individually select the voltage rail that will drive each fan. Select from Vin, 12V or 5V
• Realize Online Printing: Interfaces with a Raspberry-Pi using emulated serial over USB or direct UART to any of the serial ports on the board, to realize Klipper Firmware and Raspberry Pi Online Printing
• Motherboard Expansion Function: Support BLTouch, locked-rotor detection, shutdown after printing, resume printing after power failure, CAN bus, U disk function, IIC expansion; at the same time reserved WIFI interface, PT100 thermistor interface (optional, Only reserved interfaces, customers need to purchase chip welding, please pay attention.), dual Z-axis printer
• Increase Protection Function: Uses high-performance MOSFETs to increase heating efficiency while also reducing heat generation on the motherboard. Supports "print from SD card? and "print via USB OTG? using the integrated USB-A port

• TMC5160T V1.0 is a stepper motor driver with ultra-quiet mode and small heat
• TMC5160T V1.0 is not easy to lose step and can prevent the motor from shaking
• TMC5160T V1.0 is a high-power stepper motor drive control chip with external expansion rate MOS tube, the maximum current can reach 20A
• TMC5160T V1.0 can drive 57 stepper motors, Stepper motor torque control or sensorless homing can be achieved
• Special Note: Currently only Marlin2.0 and above firmware supports the SPI mode of the TMC5160T

• Driver Chip: BIGTREETECH TMC5160T Pro Adopts TMC5160T-TA chip, BIGTREETECH TMC5160T Pro V1.0 stepper motor driver is a high-performance stepper motor control chip with size 15.3 mm * 20.4 mm.
• Powerful Yet Low-heat: TMC5160T Pro V1.0 SPI stepper driver operates via an externally enhanced power MOSET has it, the maximum current can reach 20 A, low heat development during operation. The Maximum subdivision is 256. Supports SPI mode, & SD mode.
• Optimized Drive Performance: Based on the unique TRINAMIC functions StallGuard2, coolStep, dcStep, SpreadCycle and StealthChop, the TMC5160T Pro V1.0 greatly optimizes drive performance, comparing speed and motor torque, optimizing energy efficiency, smoothness and noiselessness.
• Excellent Option: With selectable power supply voltage from 8V to 56V(Recommended no more than 48V for safety issues), TMC5160T Pro V1.0 allows for maximum Current of 3A. Upgraded from TMC2100, TMC2130, & TMC5160 series, TMC5160 Pro V1.0 is an ideal option with higher voltage and motor current.
• Widely Compatible: BTT TMC5160T Pro stepper driver compatilbe with BIGTREETECH Octopus Pro / SKR V1.4 Turbo/SKR 3/ Manta M4P/Manta M5P/Manta M8P 3D Printer control board, support high speed / voltage printing, suitable for Voron 2.4, SV08, VZbot, CoreXY, i3 series 3D Printer.
• After-sale Services: 1-year warranty is guaranteed. If you have any queries about BIGTREETECH TMC5160T PRO V1.0 stepper motor driver, please feel free to tell us on Amazon

• Main Control Chip Features: This SKR Mini E3 V2.0 motherboard uses the STM32F103RCT6 main control chip, and its flash memory size is 256K
• CNC Fan: Because the fan on the SKR Mini E3 V2.0 control board is a CNC fan, you need to set the wind speed before using it. (Note: V2.0 version of the fan is not ready to use after power on)
• Hot-bed Mosfet: The hot bed MOS tube uses WSK220N04, low on-resistance, larger heat dissipation area, and reduce heat generation
• Upgrade Features: Support BLtouch, filament detection, power-off resume, automatic shutdown, etc.; Increase the distance between the driving chip and the components to avoid the trouble caused by the heat sink
• After-sales Support: If you encounter any problems, please write us via Amazon as soon as possible. We have professional technical after-sales personnel to solve your problems