Additive Manufacturing Products By Sovol

• Remove Excess Moisture 3D printer filaments are hygroscopic, moisture would cause printing failure. Sovol SH01, a great addition to 3d printer, can remove excess moisture, keep your filament dry and bring you better prints. The surface of prints will be smoother, the layer adhesion increased. No more brittle PLA, PETG, ABS filament
• Real-time Monitoring of Temp and Humidity inside Displays the humidity and temperature in the dry box in real time. Setting temperature 40 ?, 45 ?, 50 C and setting time from 6 hours to 12 hours. If you use SH01 in a room with room temperature under 16 degree C, the temperature in the dryer box would not come up to 50 degree C. But do not worry, this would not decrease drying effect
• Excellent Power-off Drying Mode Silicone & PTFE seal makes it possible to store filaments for a long time without power and protects your filaments from moisture and dirt. You can put 4 bags of desiccants (not included in the package) inside the dryer box to improve drying efficience & quality
• Large Capacity Sovol dryer box can store 2 filament rolls with a width of less than 70 mm or 1 filament roll with a width of less than 150 mm. Please open the PTFE seals on the top of the box during heating for Moisture evaporation
• Heating More Evenly The unique design of the built-in fan in the box is based on the principle of modynamics of air, makes the filament heated more evenly. SH01 makes drying more efficient. Any questions about the product please feel free to let us know. Our technical support team will provide service as soon as we can
• You Must Know... Place the filament into the filament outlet. Please note that the direction is placed counterclockwise so that the pulley at the bottom can feed better.If the screen displays two errors, E0 and E1, please open the drying box and check all the cable sockets on the motherboard to see if they are damaged or loose. If there is any problem, please feel free to let us know. We will send replacement for you

• Silent function( Customized and Non-standard matching)! Upgraded V4.2.7 silent board has been updated from 8 bit to 32 bit.
• Driver: TMC2225 driver. Marlin 2.0.1 and bootloader installed. You can copy the firmware file to a formated SD card with no other files in it. Turn off the printer and unplug the power cord. Insert the SD card & power cord, and turn on the printer. Wait 10s to complete the firmware updating process.
• Thermal runaway protection is enabled. The Board is Optimized by Circuit, effectively solve the Heating Problem.
• Eeay to Operate: With USB Port,can be Worked With E/Z/Y/X Axis Motor.
• Firmware 2.0.1 comes pre-installed on this board. Plug and play for Ender-3. If your printer is not Ender 3 or you would like to add a BLTouch please download the firmware here. https://www.creality.com/download

• Sovol resin vat fits for ELEGOO Mars and Anycubic Photon. The FEP film and steel ring have been preinstalled.
• Made of anodized aluminum and durable design for long term usage.
• With double silicone covers, keep the resin vat and FEP film away from dust, scratch, UV light source or direct sunlight. Perfect for resin storage.
• Clear and wear-resistance measurements, easier to use and convenient for printing. Also very easy to replace FEP film.
• Perfect spare resin vat when you need to change resin color faster and have a better printing experience.

• Remove Excess Moisture 3D printer filaments are hygroscopic, moisture would cause printing failure. Sovol SH01, a great addition to 3d printer, can remove excess moisture, keep your filament dry and bring you better prints. The surface of prints will be smoother, the layer adhesion increased. No more brittle PLA, PETG, ABS filament
• Real-time Monitoring of Temp and Humidity inside Displays the humidity and temperature in the dry box in real time. Setting temperature 40 ?, 45 ?, 50 C and setting time from 6 hours to 12 hours. If you use SH01 in a room with room temperature under 16?, the temperature in the dryer box would not come up to 50?. But do not worry, this would not decrease drying effect
• Excellent Power-off Drying Mode Silicone & PTFE seal makes it possible to store filaments for a long time without power and protects your filaments from moisture and dirt. You can put 4 bags of desiccants (not included in the package) inside the dryer box to improve drying efficience & quality
• Large Capacity Sovol dryer box can store 2 filament rolls with a width of less than 70 mm or 1 filament roll with a width of less than 150 mm. Please open the PTFE seals on the top of the box during heating for Moisture evaporation
• Heating More Evenly The unique design of the built-in fan in the box is based on the principle of modynamics of air, makes the filament heated more evenly. SH01 makes drying more efficient. Any questions about the product please feel free to let us know. Our technical support team will provide service as soon as we can
• You Must Know... Place the filament into the filament outlet. Please note that the direction is placed counterclockwise so that the pulley at the bottom can feed better.If the screen displays two errors, E0 and E1, please open the drying box and check all the cable sockets on the motherboard to see if they are damaged or loose. If there is any problem, please feel free to let us know. We will send replacement for you

• Silent function( Customized and Non-standard matching)! Upgraded V4.2.7 silent board has been updated from 8 bit to 32 bit.
• Driver: TMC2225 driver. Marlin 2.0.1 and bootloader installed. You can copy the firmware file to a formated SD card with no other files in it. Turn off the printer and unplug the power cord. Insert the SD card & power cord, and turn on the printer. Wait 10s to complete the firmware updating process.
• Thermal runaway protection is enabled. The Board is Optimized by Circuit, effectively solve the Heating Problem.
• Eeay to Operate: With USB Port,can be Worked With E/Z/Y/X Axis Motor.
• Firmware 2.0.1 comes pre-installed on this board. Plug and play for Ender-3. If your printer is not Ender 3 or you would like to add a BLTouch please download the firmware here. https://www.creality.com/download

• The gray metal extruder is an original upgrade replacement part for Ender 3, Ender 3 Pro,Ender 5,CR-10, CR-10S, CR-10 S4, CR-10 S5, CR-10 Mini, CR-10S, CR-10 Plus.
• Works better than original plastic stock extruder, make loading filament much easier. Even smoother than the red metal extruder.
• Compatible with PLA/ABS/Wood/TPU/PTEG, 40 Teeth drive gear feeds the 1.75mm filament very smoothy.
• Easy to Install. The extruder diy kit comes with a instruction on how to put it together, which makes it more easy to install.
• 100% brand new and original Creality exturder. If you have any question, please feel free to contact us.