Cutting Tools By Super Tool

• 5/8\" Carbide Tipped, 1/2\" Shank S&D Drill Bit (Silver & Deming Drill, Reduced Shank Drill)
• 1/2\" diameter by 2-1/4\" long shank allows larger diameter drills to be used in chucks 1/2\" & larger
• 118 Standard Point, 6\" Overall Length, Precision ground and USA made
• 3-1/8\" Flute Length, For Drilling Most Materials
• Carbide tips allow for higher feeds and speeds & drastically increased tool life over HSS tools.

• For counterboring and spotfacing in applications where machine requires a smaller shank
• 1/64\" Corner Radius, Tool Diameter Tolerance: +.001\"/-0\". Shank Diameter Tolerance: +0\"/-.001\"
• Pilot Hole Diameter:1/8, If using a pilot this is the shank diameter of the pilot you should choose
• Minimum Cut Diameter: .156\" Because there is a pilot hole the tool will not cut below this diameter.
• Set screw to hold a pilot or drill bit in place (if you are using a pilot or drill bit)

• 8\" overall length
• 4 3/4\" flute length
• For general purpose drilling of tough and abrasive materials.

• Tool Diameter Tolerance: +.0003\"/-0\"
• 12\" Overall Length
• 1\" Shank Diameter
• 8 Flutes
• 3.25\" Length of Flute, 7/8\" Carbide Length

• For counterboring and spotfacing in applications where machine requires a smaller shank
• 1/64\" Corner Radius, Tool Diameter Tolerance: +.001\"/-0\". Shank Diameter Tolerance: +0\"/-.001\"
• Pilot Hole Diameter:3/16, If using a pilot this is the shank diameter of the pilot you should choose
• Minimum Cut Diameter: .219\" Because there is a pilot hole the tool will not cut below this diameter.
• Set screw to hold a pilot or drill bit in place (if you are using a pilot or drill bit)

• For Counterboring most materials
• Tool diameter tolerance: +.001\"/-0\". Shank Diameter Tolerance: +0\"/-.0005\"
• Pilot Hole Diameter:1/4, If using a pilot this is the shank diameter of the pilot you should choose
• Minimum Cut Diameter: .29\" Because there is a pilot hole the tool will not cut below this diameter.
• Set screw to hold a pilot or drill bit in place (if you are using a pilot or drill bit)

• 0.5781\" Diameter
• 4 7/8\" Length of Flute
• 8 3/4\" Overall Length
• Not recommended for drilling steels

• Tool Diameter Tolerance: +.0003\"/-0\"
• 11\" Overall Length
• 1\" Shank Diameter
• 8 Flutes
• 2.875\" Length of Flute, 7/8\" Carbide Length

• 8 teeth
• 2 3/16\" overall length
• 0.279\" neck diameter
• For milling slots in most materials. Widths of 5/32\" and greater have chip breakers.
• American standard #608

• Tool Diameter Tolerance: +.0003\"/-0\"
• 9\" Overall Length
• 0.5625\" Shank Diameter
• 6 Flutes
• 2.25\" Length of Flute, 5/8\" Carbide Length

• 1-1/4\" Flute Length, 4 Flutes
• 1/2\" Shank Diameter, Weldon Flats on Shank
• 3-1/4\" Overall Length
• For milling all types of steels and steel alloys. C-5 carbide tips.Radial edged for longer tool life
• 15 Right Hand Helix, Right Hand Cut. Not a center cutting end mill.

• 0.75\" diameter carbide tipped jobber length drill 118 standard point
• 5 13/16\" length of flute
• 8\" overall length
• 3/4 diameter. Tool Diameter Tolerance: +0\"/-.0012\"
• Used by machinists and hobbyists for general purpose drilling of most materials.

• 19/32\" Carbide Tipped, 1/2\" Shank S&D Drill Bit (Silver & Deming Drill, Reduced Shank Drill)
• 1/2\" diameter by 2-1/4\" long shank allows larger diameter drills to be used in chucks 1/2\" & larger
• 118 Standard Point, 6\" Overall Length, Precision ground and USA made
• 3-1/8\" Flute Length, For Drilling Most Materials
• Carbide tips allow for higher feeds and speeds & drastically increased tool life over HSS tools.