Industrial & Scientific Store - Cutting Tools

• 60 % less effort required compared to high leverage diagonal cutters of the same size
• 40-fold increase of manual force due to special joint design
• With gripping surface below the joint for gripping and pulling wires with a diameter as from 1.0 mm
• Induction-hardened precision blades: cutting edge hardness approx. 64 HRC

• Hex Die
• Standard wrench can be used to turn hex dies
• Bright finish
• Country of origin: United States

• High Speed Steel
• Hand Reamer
• Bright Finish

• High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance
• Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge
• Round shanks allow use with a wide variety of toolholding systems
• When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging
• For general purpose drilling in applications where extra length for reach is required, designed to perform in a broad range of materials in the iron and steel families

• Made of carbon steel
• Comes with polished finish
• When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging
• Comes individually packaged
• For woodworking

• Cobalt taper shank drills are made of heat resistant cobalt.
• Engineered with heavy-duty construction to perform well in tough, hard-to-machine materials.
• Morse taper shank allows the tool to be inserted directly into the machine's spindle to facilitate high-torque applications such as large cut diameters
• When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging
• Designed to perform in a broad range of materials in the iron and steel families

• High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance
• Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge
• Morse taper shank allows the tool to be inserted directly into the machine's spindle to facilitate high-torque applications such as large cut diameters
• When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging
• Designed to perform in a broad range of materials in the iron and steel families

• High speed steel
• Split Point
• Stub (Screw Machine Length)

• High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance
• Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge
• Round shanks allow use with a wide variety of toolholding systems
• When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging
• Ideal for drilling in low and medium tensile strength materials

• Cobalt steel tools are similar to high-speed steel, but with more cobalt for improved performance when cutting harder metals such as stainless steel or nickel alloys
• Gold oxide is a thinner oxide surface treatment than black oxide typically used to identify cobalt steel tools; performance is similar to uncoated tools
• Round shanks allow use with a wide variety of toolholding systems
• When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging
• Manufactured to National Aerospace standard 907

• Carbide-tipped tools feature cutting edges of carbide for wear resistance and a steel shank for toughness
• Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications
• SDS Plus shank hammer bit
• When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging
• Especially suited for drilling in stone or concrete

• For CNC machines with BT taper spindles
• Concentricity is .0002\"
• All critical surfaces are hardened and precision ground
• Gage depth is 1.97\"
• Nose diameter is 1.18\". Drawbar thread is M16 X 2.00

• Combination of needle roller, thrust ball and deep groove ball bearings
• Central spindle is made of hardened and ground alloy steel
• Oil filler in the head for maintaining the internal bearings to extend the life of the product
• Concentricity within .0002\"
• Maximum RPM is 3000

• 3/8\" External Indexable Threading Tool Holder & Insert Kit!
• Style is SER0375E11
• Insert is 11ER A60
• Right hand external thread cut
• Kit includes 1 tool Holder, 10-TiN coated carbide inserts & 1 torx wrench