Industrial & Scientific Store - Cutting Tools

• Replaceable carbide knives to extend tool cutting life. Just replace the knives when dull or turn to sharper edge if applicable. Replaceable knives are as much as 4 times longer lasting than carbide tipped equivalent..

• Diameter (D) 1-3/16
• Cutting height (B) 1-5/8
• Shank (D) 1/2
• Overall length (L) 3-1/8
• Type Ogee

• Diameter (D): 1-5/8
• Angle (a): 45?
• Cutting height (B): 5/8
• Shank (D): 1/4
• Overall length (L): 1-3/4

• 3/32\", 7/64\" and 1/8\" pilot with 3/8\" counterbore; 9/64\" pilot with 1/2\" counterbore
• 7/64\" and 9/64\" self-centering hinge bits include replaceable HSS pilot bits
• Includes precision milled 3\" long driver bit with hardened #2 Square Drive Insert
• Engages Centrotec chuck for extremely close axial alignment of bit and output shaft of drill
• Reduced run-out and maximum torque transfer between drill and bit

• INTRODUCTION: WTTTOOLS CAT40 45?Pull Studs are strictly produced per Japanese standard MAS403. Each pull stud is tested thoroughly which ensures the quality of the pull stud.
• HIGH QUALITY: Adopted high quality low carbon alloy steel 20CrMnTi with heat treatment HRC53-60. Resistant to wear and durable which fits well on your CNC Machine and improve your working Efficiency.
• EQUISITE WORKMANSHIP: Processing thread after carburizing and quenching makes thread accurate which improves corrosion resistance and be more durable, highly extending the service life and reduce loss of this kind of pull stud.
• HIGH PRECISION: Mass production. And in order to improve efficiency and reduce wear resistence, all of our pull studs have passed serious test before sending from our factory.
• CARING SERVICE: Your pull stud retention knob have passed serious test such as nut wear test, salt spary test before sending to you. We are the manufacture of these machined tools since 2004, and have set up professional centers. If you have any problems, pls pm us via Amazon, we will try our best to make each customer satisfied. If you need other type of pull stud, pls pm us directly.

• Insert carbide rabbeting bit with 3/8-inch cutting depth
• 1-3/8-inch diameter and 1/4-inch shank
• Simply change bearing to produce different rabbets on wood and wood composites
• 3/8-inch depth rabbeting bit indexable knife

• High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance
• Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications
• Round shanks allow use with a wide variety of toolholding systems
• When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging
• Used to align existing holes prior to bolt or rivet installation

• Direction down-cut
• (D) diameter 1/4
• (B) Cutting height 2-1/4
• (D) shank 1/4
• Overall length (L) 4

• Smooth and easy carving, even in hard wood
• Tungsten carbide with easy replacement & very good life. Just rotate the carbide a bit when the tip eventually wears
• Three 5mm diameter cutting tips on a 26mm head with shaft. Max 25,000 rpm
• Ideal for a Die Grinder, or other tool that takes a 1/4 inch shank. Max. Carving Depth : 32 mm
• Includes shafted Cutterhead with 3 carbides and torx driver for tightening carbides

• 1 3/16\"-16 HSS right hand thread tap

• The 5PCS carbide CNC router bits set with 1/4 inch shank
• This spiral router bit set includes 3pcs end mill and 2pcs flush trim bits, you can use them on different projects.
• End mill bits can smoothly upcut and downcut groove and slots, mortises, cycles and dados with clean edge and bottom, better than straight bits.the flush trim bit perfect use for wood trimming.
• The CNC end mill router bits apply to various wood: such as Plywood, OAK, MDF, and any hardwood working.
• The CNC router bit made of solid carbide, with C3 Micro-grain tungsten carbide, high heat resistance and wear resistance, good rigidity, not easy to break.