Industrial & Scientific Store - Additive Manufacturing Products

• The filament is for 3D printing pen or 3D Printer and used to melt plastic at a high temperature.
• Length: 5 meter; Diameter: 1.75mm
• Color: Yellow ; Temperature; 190 degreeC - 230 degreeC
• Note: Due to light and screen difference, the item's color may be slightly different from the pictures. Please allow 10-50mm deviation due to manual measurement.

• Excellent soft texture ,with high resilience.
• Anti-UV, no smelling and environmental-friendly

• Material: PLA
• The filament is for 3D printing pen or 3D Printer and used to melt plastic at a high temperature.
• Length:5 meter; Diameter: 1.75mm
• Color: Silver ; Temperature; 190 degreeC - 230 degreeC
• Note: Due to light and screen difference, the item's color may be slightly different from the pictures. Please allow 10-50mm deviation due to manual measurement.

• Customer Care: 9670411510

• Has therapeutic properties Good Thermal and Chemical Insulation.
• Temporary Seal Rapid Setting Radiopaque Zinc Oxide
• For lining under non-resin filling materials. As a temporary filling material and cement. As a temporary seal.
• Therapeutic properties - ideal for sensitive cavity. Good thermal and chemical insulation. Strong base for amalgam condensation, higher initial resistance to fracture due to resin bonding.

• Material: Brass
• Pitch: 2mm (Single Start Threads); Inside Diameter: 8mm; For actual dimension please see diagram in photos
• Thread Type: Trapezoidal Metric Thread; Spring loaded Anti Backlash Nut
• Application: 3D Printer, CNC, Robotics, DIY Projects etc
• Package Include: 4 x Tr8 Anti Backlash Nut

• Material: Silicon Rubber
• Size: 300 x 300 MM
• Voltage: 220 V
• Power: 340 W
• Suitable for 3D printer Bed

• Material: PLA
• The filament is for 3D printing pen or 3D Printer and used to melt plastic at a high temperature.
• Length:10 meter; Diameter: 1.75mm
• Color: Black ; Temperature; 190 degreeC - 230 degreeC
• Note: Due to light and screen difference, the item's color may be slightly different from the pictures. Please allow 10-50mm deviation due to manual measurement.

• Fit for 42mm NEMA 17 stepper motor
• Material: Alloy steel
• Size: 5X5X5cm(L*W*H)
• Sheet Thickness : 2mm
• Suitable for CNC 3D printer stepper motor.

• Material: PLA
• The filament is for 3D printing pen used to melt plastic at a high temperature
• Length:10 meter; Diameter: 1.75mm
• Color: White; Temperature; 190 degreeC - 230 degreeC
• Note: Due to light and screen difference, the item's color may be slightly different from the pictures. Please allow 1-5mm deviation due to manual measurement.

• It is 1.4 3D Printer Control Panel
• Durable Construction
• Easy to use

• This is including 5pcs Limit Switch Kit For Ender-3/Ender-3 S/Ender-3 Pro/Ender-3 V2/Ender-3 Max/CR-10/CR-10 V3/CR-10 S4 and other suitable 3D Printers
• They are original from creality, high quality switching element,Sensitive trigger, Quiet, high precision, high repeat positioning accuracy.
• 3Pin N/O N/C Control, Reliable performance, easy to use, durable, long serice Life.
• Package: 5pcs limit switches

• Easy to Remove Model within 1 Minute: The coating of the microporous composite material has a microporous structure. The filament will be 'extruded' due to the reduction of platform temperature and shrinkage of composite materials, which makes the model remove easily.
• High Viscosity and Strong Adhesion: Composite nano molecule coating has high viscosity after heating, which makes the model have strong adhesion.
• 0.15MM of Flatness Recovery Model: This is the combination of glass and composite. Due to the flatness of glass and the uniform composite coating of surface 'lattice', the platform has excellent flatness.
• Wear-Resistant and Scratch-Resistant, easy to clean: There is a protective film on the surface of the composite coating, which is of anti-scratch and dustproof, etc.
• High Hardness and Durable: This is the combination of chemically tempered glass and surface composite coating. The flatness of glass will be much better and the composite coating of surface 'lattice' will be uniform, which makes the platform have excellent flatness.

• TMC2208 is an ultra-quiet two-phase stepper motor drive chip, continuous drive current 1.4A, peak current 2A, voltage range 4.75V-36V, 256 subdivision.
• The flexible microPlyer interpolation unit provides up to 256 subdivisions, allowing perfect sinusoidal control even in systems with limited pulse frequencies; these are also designed because stealthChop2 ultra-quiet technology is widely used in 3D printing.
• Compatible with existing 3D printer electronics, eliminating the expensive costs of redesign. It can replace the original TMC2100 A4988 DRV8825 LV8729, lower heat, especially for 3D printing market.
• With this adapter you can test your SilentStepStick or flash the TMC2208 SilentStepStick with an USB-to-serial converter.
• The adapter comes with stackable headers, so you can use it direct on your 3D printer board. The tester is pre-configured for standalone operation on an USB to serial adapter (VIO-VM jumper closed).

• Package content: you will get 10 pieces of 3D printer silicone covers in black color, compatible with MK7, MK8, MK9 Makerbot heater block, enough to meet your needs
• Silicone cover: the heater block cover is made of heat-resistant, non-stick silicone material, its high-temperature resistance is 280 Celsius degree
• Function: the silicone cover will keep your heater block clean and repel plastic of burnt, and build-up, so that can extend the life of the heater block, and help to keep the hot end temperature stable
• Compatibility: our heater block covers fit for 0.78 x 0.78 x 0.39 inch/ 20 x 20 x 10 mm heater block, compatible with Creality CR10/ CR10 S4/ CR10 S5/ CR 10 mini/ Ender 2/ Anet A8, etc., and for other MK7, MK8, MK9 hot end; Please confirm the size before purchase
• Durable to use: the silicone case has good flexibility and can be placed close to the heating block, it is easy to install, stable and not easy to fall off, very strong.

• UPGRADE: Perfect replacement for Creality 3D Printers Ender 3, CR-10 and CR-10S Series.
• STABLE and DURABLE: Full metal aluminum alloy, DIY kit and you need to assemble by yourself. Our MK8 extruder hotend include all the necessary screws & parts needed to directly replace your old original weak Creality plastic extruder.
• EASY TO INSTALL: All you do is unbolt the old original Creality plastic extruder & screw in the new \"Metal Extruder\" and ready to start printing. Used for 1.75mm filament of 3D printer MK8 bowden extruder frame.
• ADVANTAGES: The advantages of our extruder drive is you have better stronger pressure pushing the filament into the printer nozzle and so will improve on the printers' performance. Our extruder kits have an adjustable bolt so that you can adjust the pressure of the extruder gear as needed.
• This extruder feeder drive is compatible with nearly all models of 3D printers. No need to change stepper motors or other mounting hardware.