Expansion Joint Fillers By INVENTO

• Outside Diameter: 5mm
• Length: 600 mm (0.6 meter)
• Material: EN-31 (Hard Chromed)
• Qty: 8pcs
• Application: 3D Printer, CNC, Robotics, DIY Projects etc

• Diameter: 12"
• Slope: 4.5 "(11.43 cm)
• Bore: approximately 5mm, 6mm or 7.8mm motor shafts (come with the prop shaft washer,you can use for different shaft)
• Note: Color of product may be different from picture, if you need any specific color please contact before ordering.
• Package Include 4 pair 12 Inch Propeller

• Working Voltage: 5V
• Working Current: <25mA
• High Power-Dissipation Capability
• Low frequency, High efficiency
• Package Include 10 x Buzzer

• Cat5/Cat6 Cable to BNC Female Connector for CCTV camera connection.
• Cost Effective - use Cat5/Cat6 cable to replace traditional RG59/RG6 coaxial cable.
• Simply & Professional! Easy to use & install, save time and save money
• Support all video devices, such as camera, monitor, DVR card and recorder etc
• Package contents: 10x BNC Female Connector

• Outside Diameter: 8mm
• Length: 400 mm (0.4 meter)
• Material: EN-31 (Hard Chromed)
• Package Include 2 x 8mm OD 400mm long Smooth Rods
• Application: 3D Printer, CNC, Robotics, DIY Projects etc

• Wire length: 250 mm on both male and Female connector
• Package contents: 8 sets of male (8pcs) & Female JST Connector (8pcs)
• Best for Led Lights & DIY Projects
• Note: Wire colour can be different from the picture as item will be supplied as per stock. if you have specified color requirement then please contact us before placing an order.

• The 74HCT85D is a 4-bit CMOS Magnitude Comparator pin compatible with low power Schottky TTL (LSTTL). It can be expanded to almost any length. It performs the comparison of two 4-bit binary, BCD or other monotonic codes and present the three possible magnitude results at the outputs. The 4-bit inputs are weighted, where A3 and B3 are the most significant bits.
• The upper part of the table describes the normal operation under all conditions that will occur in a single device or in a series expansion scheme. In the upper part of the table the three outputs are mutually exclusive. In the lower part of the table, the outputs reflect the feed forward conditions that exist in the parallel expansion scheme.
• Logic Family / Base Number: 74HCT85; Comparator Type: Magnitude; No. of Channels: 4Channels; No. of Bits: 4bit.
• No. of Pins: 16Pins; Supply Voltage Min: 4.5V; Supply Voltage Max: 5.5V; Logic IC Base Number: 7485.
• Package Include 2 x 7485 IC

• Outside Diameter: 6mm
• Length: 600 mm (0.6 meter)
• Material: EN-31 (Hard Chromed)
• Qty: 2pcs
• Application: 3D Printer, CNC, Robotics, DIY Projects etc

• Small sensor can detect horizontal tilt, vertical flip, shock and vibration. It is formed by two contacts and two small metal spheres. When the sensor is in a horizontal position, the spheres connect contacts between them (ON-state), closing the circuit, when it is tilted more than 15 degree the contacts open (OFF-state). It is widely used in toys, small appliances, and anti-theft detection systems but also in smart-car and robot-car.
• Operating voltage: <12V; Current tolerated < 20mA
• Conduction time: 2ms; Contact resistance (closed): <10m?; Contact resistance (open): >10M?
• Operating temperature range: -40 ~ +80 degree C; Operating lifespan: 100,000
• Package Include 10 x Tilt Sensor Switch

• The BD140 from Multicomp are through hole, PNP power transistor in TO-126 metal can package. This device is usd for medium power, linear and switching applications.
• Collector to emitter voltage (Vce) is -80V. Collector current (Ic) is -1.5A
• Power dissipation (Pd) is 12.5W. Collector emitter saturation voltage of -500mV at Ic=10mA.
• Operating junction temperature range from -55 degreeC to 150 degreeC
• Package Include: 5 x BD140

• The SN74HC05N is a 1-input 14-pin Hex Inverter made of CU NIPDAU lead/ball finish. The device contains six independent inverters. It performs the Boolean function Y = A in positive logic. The open-drain outputs require pull-up resistors to perform correctly.
• It may be connected to other open-drain outputs to implement active-low wired-OR or active-high wired-AND functions.
• Logic Family / Base Number: 74HC05; Logic Type: Inverter; Output Current: 25mA; No. of Inputs: 1
• Supply Voltage Min: 2V; Supply Voltage Max: 6V; No. of Pins: 14Pins; Logic IC Base Number: 7405
• Package Include 5 x 7405 IC

• These devices are designed for high??voltage, high??speed power switching inductive circuits where fall time is critical. They are particularly suited for 115 and 220 V SWITCHMODE applications such as Switching Regulators, Inverters, Motor Controls, Solenoid/Relay drivers and Deflection circuits.
• Reverse Biased SOA with Inductive Loads @ TC = 100C; 700 V Blocking Capability.
• Inductive Switching Matrix 0.5 to 1.5 A, 25 and 100C tc @ 1 A, 100C is 290 ns (Typ)
• Collector Emitter Voltage V(br) ceo: 400V; Transition Frequency ft: 10MHz; Power Dissipation Pd: 1.4W; DC Collector Current: 1.5A; DC Current Gain hFE: 4hFE.
• Package Include 10 x MJE13003

• Voltage: DC 3.7V
• Speed:46500 RPM(DC 4.2V), 40000 RPM(DC 3.7V
• Motor diameter: 6mm; Motor length: 12mm
• No-load current: 0.04A
• Package Include 4 x Motor. Note: when you install the propeller, press and hold the back of the motor to prevent damage to the motor.