Construction Equipments - Borewell Equipment Manufacturers Products

• No man power is required as it is operate as fully automatic water level controller for tank, so dont worry about overflow
• Water level indication provided to see water level in tank
• Also suitable for single phase MCB starter panel & submersible motor.
• Auto and Manual Switch Provided

• Features Designed for under submerged condition water applications All rotating parts are dynamically balanced for longer bearing life and Vibration free smooth operation Epoxy ceramic coated in the inner parts for rust free operation Fitted with Quality Oil seal Easy for installation and no platform required Designed to withstand wide voltage fluctuations Non overloading power characteristics no fear of motor burning
• Topping up the motor Unscrew the Brass Plugs 1 and 2, fitted on top of the motor as shown in Fig. 1 below, and fill the motor with pure drinking water till water overflows from the other filling hole. Gently rock the motor to release air bubbles and further top up if necessary. Then replace the two plugs.
• The brass Plug 3 mounted on the bottom of the motor, is used for draining the water from within the motor. Ensure all three Brass Plugs are tightened to prevent leakage of water from within the motor. Check for leakages before lowering the OWS. Use prescribed pipe sizes as mentioned on the product name plate. Check the level of silt at the bottom of the well. Refer Fig. 2, shown below, for locating the OWS for operation with flooded suction
• Use the eye bolts / lifting lugs for lifting / lowering the OWS using appropriate equipment. Keep the wire ropes remains tied for lifting of the pump set for future. To prevent the motor from getting exposed during pumping, ensure the suction strainer is fitted above the level of the motor. This is done by fitting one end of a bend to the pump suction flange and the strainer to the other end of the bend, thereby ensuring that the level does not fall below the strainer.
• Water proofing the submersible motor cable - supply cable joint DOL OWS Motors are supplied with a single 3 core PVC insulated flat cable of length 3 meters. The free end of the 3 core cable of the motor needs to be connected to the supply cable from the control panel. As this joint is always nearly submerged in water, the joint needs to be water proof.
• SD OWS Motors are provided with two separate 3 core PVC insulated flat cable, each of 3 meters length. Repeat the procedure for both 3 core PVC flat cables from the motor to the two cables from the Control Panel.
• Electrical installation As far as possible, do not use multiple joints in the electrical cabling while connecting the Control Panel to the OWS. Ground the pump set using the two earth screws provided on the leg of the motor body. Ensure electrical joints, if any, are properly and adequately insulated. Connect the cable properly to the starter terminals to avoid loose connections. Factor in low voltage operation while selecting cable size.
• Checking rotation of OWS Power up the OWS and observe the discharge from the pump. Next interchange any two phase wires, power up the OWS and observe the discharge from the pump. In case the discharge is more after interchanging any two phase wires, then the impeller is rotating in the correct direction within the volute casing. If the discharge after interchanging any two phase wires is lower, then the previous phase wire connection was correct. Now revert back to the old phase wire connection.

• High resolution with 1/9 CMOS camera. Built-in 6 LED light (with Brightness and take Photo Control)
• Waterproof wire endoscope. Photo shooting and video recording.
• 8.0mm waterproof wired camera can inspect area under water, gaps and holes. 8pcs adjustable LED lights instead of 6 LED lights for clearer image experience in dark area.
• Important Notes: For Android 10+ system, please download MScopes, AN98 or OTG View(special version for Android 10)from official google play. For system lower than Android 10, please download Camerafi2, MScopes from official google play.
• 5M semi-rigid cable, 360 degrees rotation to choose view angel easily.

• Product Information - Domestic Submersible Pump 3HP 35 STAGE 1" Outlet 220 Voltage Single Phase
• Phase - Single phase Submersible Water Pump 3 HP
• Body Material - Stainless Steel | Impeller - Noryl
• Use at 300 feet water give 3500 LPH , Use at 400 feet water give u 3000 LPH , Use at 500 feet water give u 1800 LPH ,Use at 600 feet water give u 500 LPH
• Warranty Summary - 1 Year Warranty from the date of purchase

• Water pumps for domestic use

• Material : HDPE , Color : White
• Light in weight, Easy to carry around from one place to another
• Used to watering plants in terrace, balcony, ground, garden space.
• UV Coated
• Puncture Resistant, Crack proof , Resistant to abrasion and kinks

• 1 year warranty ; Compact Robust?Easy for everyday professional measuring solutions
• Measuring Range: 0.15-40m and Measuring accuracy +/-2mm. Magnetic: No
• Measuring time <0.5sec and automatic shut down 5 mins
• Laser class 2, Laser type 635nm and display backlight, Buzzer
• Application:Length measurement, continuous measurement, area measurement, volume measurement and simple pythagoras measurement
• Package Contents: 1 Measuring Device, 2 AAA batteries (1.5 V LR03)

• Easy to install
• Material: PVC, Color: White
• Package Contents:1 Water Hand Pump
• Best for individual use at Home, Garden, Shop
• Its with all required accessories you just need to drill 4 holes and it's ready to use

• Energy efficient motor, Motor speed: 2900 Revolution per minute. In built thermal overload protector : Yes. Motor stator : Low Watt loss silicon steel lamination
• Copper Winding
• High grade pump castings (FG-200 grade) ensures very slow rusting of pump, pump life increases due to less rusting and wear and tear
• Stainless Steel Shaft (SS-410) of the pump set protects the pump shaft from rusting due to hard water
• An ISO 9001:2015 Certified Company
• Maximum Output: 3400 liters / Hour
• Operating Voltage : 220V, Power Consumption Max 3.2A. Cast Aluminium Body.
• 2 Year Warranty

• Special Use: - Unlike other submersible pump that requires to be water submerged, this pump functions well in dry condition and can be used to empty water clog. Perfect for dewatering cooler, aquarium, pond, etc. L shaped nozzle in the front will help you drain out water from unreachable locations with the help of pipe
• 100% Pure Copper Winding: - No Aluminum and No CCA, pure copper winding motor enhance pump durability by enabling lower temperature operation.
• Thermal Protection: - Our product comes with inbuilt thermal protection, which means when the pump sense temperature rise of up-to 75 degreeC it will stop working; it will automatically restart when back at normal temperature of 45 degreeC
• Premium Built Quality: - Pump is made from non-recycled high quality ABS plastic and provided with 2 m long pure copper wire which makes it easy to install pump in deep water locations. This pump is more durable against environmental wear and tear
• Super Silent Operation: -Due to high quality parts and copper winding our pump runs significantly silent compared to other pump with noise level of <25db
• Detachable and Cleanable: - No-tool detachable makes the cleaning process even easier as you do not require any tool to detach and reassemble the pump. Also, regular cleaning enhances the product's life.
• Warranty: - The products come with 2 year warranty (To claim warranty contact us via call or whatsapp, number available below in 'Product Information' section.)

• Energy efficient motor, Motor speed: 2900 Revolution per minute. In built thermal overload protector : Yes. Motor stator : Low Watt loss silicon steel lamination
• Copper Winding
• High grade pump castings (FG-200 grade) ensures very slow rusting of pump, pump life increases due to less rusting and wear and tear
• Stainless Steel Shaft (SS-410) of the pump set protects the pump shaft from rusting due to hard water
• An ISO 9001:2015 Certified Company
• Maximum Output: 2000 liters / Hour
• Operating Voltage : 220V, Power Consumption Max 3.2A. ALUMINIUM BODY.
• 1 Year Warranty

• 100% Pure Copper Winding
• ISI Marked - Thermal Overload Protector
• Stainless Steel Motor Shaft with Double Shielded Ball Bearings
• Multiple Use - Home, Garden, Car Washing, Domestic Water Supply, etc
• High Speed Water Supply - 1800 Litres Per Hour, & Head Size - 25mm

• Features Designed for under submerged condition water applications All rotating parts are dynamically balanced for longer bearing life and Vibration free smooth operation Epoxy ceramic coated in the inner parts for rust free operation Fitted with Quality Oil seal Easy for installation and no platform required Designed to withstand wide voltage fluctuations Non overloading power characteristics no fear of motor burning
• Topping up the motor Unscrew the Brass Plugs 1 and 2, fitted on top of the motor as shown in Fig. 1 below, and fill the motor with pure drinking water till water overflows from the other filling hole. Gently rock the motor to release air bubbles and further top up if necessary. Then replace the two plugs.
• The brass Plug 3 mounted on the bottom of the motor, is used for draining the water from within the motor. Ensure all three Brass Plugs are tightened to prevent leakage of water from within the motor. Check for leakages before lowering the OWS. Use prescribed pipe sizes as mentioned on the product name plate. Check the level of silt at the bottom of the well. Refer Fig. 2, shown below, for locating the OWS for operation with flooded suction
• Use the eye bolts / lifting lugs for lifting / lowering the OWS using appropriate equipment. Keep the wire ropes remains tied for lifting of the pump set for future. To prevent the motor from getting exposed during pumping, ensure the suction strainer is fitted above the level of the motor. This is done by fitting one end of a bend to the pump suction flange and the strainer to the other end of the bend, thereby ensuring that the level does not fall below the strainer.
• Water proofing the submersible motor cable - supply cable joint DOL OWS Motors are supplied with a single 3 core PVC insulated flat cable of length 3 meters. The free end of the 3 core cable of the motor needs to be connected to the supply cable from the control panel. As this joint is always nearly submerged in water, the joint needs to be water proof.
• SD OWS Motors are provided with two separate 3 core PVC insulated flat cable, each of 3 meters length. Repeat the procedure for both 3 core PVC flat cables from the motor to the two cables from the Control Panel.
• Electrical installation As far as possible, do not use multiple joints in the electrical cabling while connecting the Control Panel to the OWS. Ground the pump set using the two earth screws provided on the leg of the motor body. Ensure electrical joints, if any, are properly and adequately insulated. Connect the cable properly to the starter terminals to avoid loose connections. Factor in low voltage operation while selecting cable size.
• Checking rotation of OWS Power up the OWS and observe the discharge from the pump. Next interchange any two phase wires, power up the OWS and observe the discharge from the pump. In case the discharge is more after interchanging any two phase wires, then the impeller is rotating in the correct direction within the volute casing. If the discharge after interchanging any two phase wires is lower, then the previous phase wire connection was correct. Now revert back to the old phase wire connection.

• This product will be an excellent pick for you
• It ensures a hassle-free usage
• This product comes in a safe packaging

• Material:Aluminium, Color:Grey